ORiNG PET-102GT Plus Plus Quick Installation Manual

Extender
HIGH POWER POE++
Q I
I N D U S T R I A L uick nstallation
Introduction
The is a high power PoE extender and compatible with
PET-102GT++
IEEE802.3at/af standard. With one 10/100/1000TxBase-T(X) P.D. input port
and two 10/100/1000TxBase-T(X) P.S.E. output ports, the device can not only
deliver Ethernet data but also forward power from the previous PoE device
to the next device. Furthermore, the
external DC power sources. By using external DC power to compensate for
power losses caused by long-haul transmission, users can continue to use
the PoE extender to enlarge the distance unlimitedly. With the ability to
provide 90Watts PoE power per port, the
friendly and high-power PoE extender.
Features
Support 1 port PoE P.D. input to 2 port POE P.S.E output with 10/100/1000Base-T(X)
for power and data extender
Supports P.S.E. based on IEEE 802.3af/at standard
PoE P.D. input support 90watts max.
PoE P.S.E. output support 90watts max. per port
Support auto-negotiation and auto-MDI/MDI-X
Multiple unit , daisy-chain installation support
High reliability and rigid IP-30 housing
DIN-Rail and wall mounting enabled
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents Pictures
PET-102GT++
QIG
DIN-rail kit
Wall-Mount Kit
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Q I G
PET-102GT++
PET-102GT++
G
uide
Reduced Air Flow:
equipment is not compromised during installation.
Mechanical Loading:
condition due to uneven mechanical loading.
PET-102GT++ can be powered by
Circuit Overloading:
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
PET-102GT++ is surely a user-
Dimension
PET-102GT++
Number
Panel Layouts
X 1
Front Panel
X 1
PET-102GT++
1
2
3
4
X 1
5
6
X 2
7
Rear Panel
2
1
2
1907-2-29-PET102GT++-1.0
ICP Deutschland GmbH | +49(0)7121-14323-20
Make sure the amount of air flow required for safe operation of the
Make sure the mounting of the equipment is not in a hazardous
Consideration should be given to the connection of the equipment to
34.7 17.3 23.0
40.0
25.0
5.0
1. Power LED
2. LNK/ACT indicator for P.D. port
3. P.D. port
4. PoE status LED for P.D port
5. LNK/ACT indicator for P.S.E. port
6. P.S.E. LED
7. PoE status LED for P.S.E port
Top Panel
1. Terminal block
1. Din-rail screw holes
2. Wall-mount screw holes
1
PRINTED ON RECYCLED PAPER
| sales@icp-deutschland.de
Industrial High Power Extender
Installation and Distance
Power input on the first unit
50VDC
P.D. attached on the last unit
IEEE802.3at (25.5W) Extended 2 unit
Max. Distance up to 300 meters
IEEE802.3af (12.95W) Extended 4 units
Max. Distance up to 500 meters
NO P.D. on the last unit Extended 5 units
Max. Distance up to 600 meters
Note : The test result is with one P.D. device connected to the last unit and only for reference.
Example for 57VDC power input and attached IEEE802.3at P.D.
DIN-rail
Step 1 : Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2 : Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into
the rail firmly.
Wall-mount
Step 1: Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
eight
total of screws are required, as shown below.
Step 2: Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Step 3: Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
| www.icp-deutschland.de
Version 1.0
57VDC
Extended 3 units
Max. Distance up to 400 meters
Extended 5 units
Max distance up to 600 meters
Extended 6 units
Max. Distance up to 700 meters
PET-102GT++
Quick Installation Guide