Luna APF161 Instruction Manual

7. Remove the 4 screws located on the

operation

front of the motor unit. Place the rear grille
Make sure that you read all of the safety
into position on the motor unit (handle up),
warnings before you operate this unit for the
then secure into position with the 4 screws
first time. Plug the unit to a standard mains
provided.
socket and turn on the mains switch.
off / Speed Switch
Rear Grille
1. Turn the rotary switch on the top of the
motor unit to select between fan speeds:
0 (OFF ),1, 2 or 3.
0= off
Grille
1= Low Speed
Screws
2= Medium Speed
3= High Speed
8. Remove plastic sleeve from motor shaft,
then place the fan blade on the motor shaft,
aligning the flat on the shaft with the fan blade
screw. Securely tighten the fan blade screw.
Fan Blade
oscillation Control
2. Push the oscillation knob downward to allow
the motor unit to oscillate horizontally through
approximately 80° angle. Lift oscillation knob
upward to turn off oscillation mode.
Fan Blade
Screw
9. After loosening, remove the fixing screw and nut
from the bottom of the front grille. Place the front
grille over the rear grille, press grille retaining clips
into position, then tighten grille fixing nut and screw.
Ensure that the fan blade is entirely enclosed and the
complete grille is securely in position. Oscillation
Knob
Front
Grille
Vertical Direction of Motor Unit
Grille
3. The vertical direction of the motor
Retaining
unit can be adjusted by loosening the tilt
Clips (4)
adjustment knob, tilting the complete head
unit (incorporating motor unit and assembled
grille) forward or back ward until the desired
direction is reached, then tightening the tilt
adjustment knob.
Grille Fixing
Screw & Nut
5
Tilt
Adjustment
Knob
Height adjustment
4. The fan height can be adjusted by loosening
the height adjustment knob, lifting the inner
pole (with attached motor unit) and then
tightening the height adjustment knob when
Off/Speed
the desired height is obtained.
Switch
C
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product ("you") from a retailer that this product will be free of defects in
materials and workmanship for a period of 12 months from the date of purchase; provided the product is not used other than for the
Off purpose, or in a manner not within the scope of the recommendations and limitations, specified by Arlec, is new and not damaged at the
time of purchase, has not been subjected to abuse, misuse, neglect or damage, has not been modified or repaired without the approval
of Arlec and has not been used for commercial purposes ("Warranty").
If you wish to claim on the Warranty, you must, at your own expense, return the product, and provide proof of original purchase and
your name, address and telephone number, to Arlec at the address below or the retailer from whom you originally purchased the
product within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the above manner and if, in Arlec's reasonable
opinion, the Warranty applies, Arlec will at its own option and expense (or authorise the retailer to) replace the product with the same
On
or similar product or repair the product and return it to you or refund the price you paid for the product. Arlec will bear its own expenses
of doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to which the Warranty
relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 ("Arlec") gives the Warranty.
Arlec's telephone number, address and email address are:
Customer Service: (03) 9982 5111
New Zealand Toll Free: 0800 003 329
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: custservice@arlec.com.au
Care & MaintenanCe
1. Always disconnect the cord from
the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from
the fan with a soft cloth or vacuum cleaner us-
ing the dusting brush attachment.
3. Wipe the exterior surfaces of the fan
occasionally with a cloth moistened
(not dripping wet) with a mild soap solution.
Dry the case thoroughly with a soft dry cloth
before operating the fan.
4. Avoid the use of gasoline, benzine, thinner
etc as they may result in damage to the fan.
5. Store the fan in a clean dry place when not
in use.
Warning: Do not immerse the fan in water or
allow water to drip into the interior of the fan
housing as this could create a fire or electric
shock hazard.
Height
Adjustment
Knob
CPIN002920
6
L
una
Stainless Steel
Pedestal
Fan
40cm
Instruction Manual
Model APF161
Important! Please read these instructions carefully
CPIN002920