Summary of Contents for MTN Products Horizons Counter Top
- Page 1 MTN Products Horizons Counter Top Complete Manual Cooler Disassembly Instructions Included ...
-
Page 2: Table Of Contents
Horizons® C ounter T op C omplete M anual Table of Contents TABLE OF CONTENTS ......................I TECHNICAL SPECIFICATIONS ................... 1 ....................1 LECTRICAL PECIFICATIONS ......................... 1 EFRIGERANT .......................... 1 ATER ..........................1 ATER GENERAL INFORMATION .................... -
Page 3: Technical Specifications
Horizons® C ounter T op C omplete M anual Technical Specifications Electrical Specifications Voltage: 115 VAC, 60 Hz Current: 5.6 Amps Wattage: 640 Refrigerant R134a refrigerant 1.6 oz. charge Cold Water Reservoir: 3.5L Seam Welded 304 Stainless Cold Water Temperature: 45°F ARI Cooling Capacity: 0.5 gph at 50°F Hot Water... -
Page 4: General Information
Horizons® C ounter T op C omplete M anual General Information • This POU should only be connected to a potable water source. • Unit to be used indoors only. • Do not locate unit in direct sunlight or next to a heat source. •... -
Page 5: Getting To Know The Interface
Horizons® C ounter T op C omplete M anual Getting To Know The Interface Dispense nozzle bottom portion LED. Panel brightness adjustment (3 variations). Cold water dispense button. Cold water indicator. LCD information display screen. Hot water indicator. -
Page 6: Installing The Horizon Counter Top Unit
Horizons® C ounter T op C omplete M anual Installing the Horizon Counter Top Unit Note: Ensure installation complies with all State and Local Plumbing Codes. • Locate cold water supply line and install suitable access valve with a ¼” outlet with shutoff. -
Page 7: Programming The Horizon® Counter Top Cooler
Horizons® C ounter T op C omplete M anual Programming The Horizon® Counter Top Cooler Note: All programming is accomplished using the three buttons located directly below the LCD display screen. VERY IMPORTANT: After each change is made, the “Setup” button must be pressed for programing to be accepted. - Page 8 Horizons® C ounter T op C omplete M anual Programming The Horizon® Counter Top Cooler Continued • Press “Setup” button again and Hot-Temp Adjustment will appear on the “LCD”. Factory default is 88°C (190°F). Adjust range is 82°C (180°F) to 89°C (192°F). Use the “Up”...
-
Page 9: The Rear Panel
Horizons® C ounter T op C omplete M anual Rear Panel 7 ... -
Page 10: Understanding The Dispense System
Horizons® C ounter T op C omplete M anual Understanding the Dispense System The Horizons® CT Water System 8 ... -
Page 11: Disassembly
Horizons® C ounter T op C omplete M anual Disassembly Note: Always drain the Cooler. Hot Tank Drain Location Hot tank drain is located under the cooler. To prevent scolding, use needle nose pliers to remove plug. -
Page 12: Side Panel Removal
Horizons® C ounter T op C omplete M anual Disassembly Continued Side Panel Removal Each side panel is attached with two screws. To remove panel, tilt cooler and remove the two screws using a Phillips #2 screwdriver. Push down on panel to remove. Side panels are interchangeable. -
Page 13: Front Panel Removal
Horizons® C ounter T op C omplete M anual Disassembly Continued Front Panel Removal The front panel is attached with 6 screws. The 4 yellow arrows point to sheet metal screws, and the 2 red arrows are machine screws. Use a #2 Phillips to remove all screws. -
Page 14: Accessing The Lcd Circuit Board And Dispense Solenoid
Horizons® C ounter T op C omplete M anual Disassembly Continued Accessing the LCD Circuit Board and Dispense Solenoid After the 6 screws have been removed from front panel, pull the panel forward to gain access to circuit board and dispense solenoid. -
Page 15: Rear Panel Removal
Horizons® C ounter T op C omplete M anual Disassembly Continued Rear Panel Removal Rear panel is secured with six screws, three per each side. Four are sheet metal type (yellow arrows), and two machine screws (red arrows). Hint: When installing the panel, install machine screws first for proper panel alignment. -
Page 16: Accessing The Horizons® Counter Top Main Pcb
Horizons® C ounter T op C omplete M anual Accessing The Horizons® Counter Top Main PCB The PCB is attached with four screws. Should replacement be necessary, remove the four screws and pull the board out with wiring attached. Install the new board and transfer wires from the old to new board. -
Page 17: Parts Location
Horizons® C ounter T op C omplete M anual Parts Location 1. Cold Water Pump. 2. Hot Water Pump. To gain access to cold control, remove the black colored Phillips head screw (yellow arrow). - Page 18 Horizons® C ounter T op C omplete M anual Parts Location Continued To access the hot controls, remove front panel than remove hot control cover. The hot thermostat (thermistor) is located on top, and the heat limiter is on the bottom. Should heat band need to be replaced, cut the lower strap on the hot tank insulation and roll insulation up.
-
Page 19: Troubleshooting
Horizons® C ounter T op C omplete M anual Troubleshooting Water not dispensing Check float assembly has not been tripped. Press reset button on float assembly to reset float. Verify cooler connected to a working outlet. Verify that the water shut off valve leading to unit has not been shut off. - Page 20 Horizons® C ounter T op C omplete M anual Troubleshooting Continued If water continues to boil shut off hot tank switch. Repairs should only be completed by a certified technician. For additional troubleshooting assistance contact technical@mtnproducts.com ...
-
Page 21: Wiring Diagram
Horizons® C ounter T op C omplete M anual Wiring Diagram 19 ... - Page 22 MTN Products Horizons Counter Top Complete Manual Cooler Disassembly Instructions Included ...
Need help?
Do you have a question about the Horizons Counter Top and is the answer not in the manual?
Questions and answers