Table of Contents
Advertisement
UT50 Fully Rugged Windows Tablet Quick Start Guide
Unpacking
1. One UT50 Fully Rugged Windows Tablet Unit
2. Two Battery Packs
3. One AC Adapter
4. Power Cord (US/UK)
5. One Digitizer Pen
6. One Hand Strap
NOTE: This package does not include headset.
Front and Rear Views
A: Double Channel Speakers
B: Light Sensor
C: Front Camera
D: Microphone
E: Front Camera Indicator LED
Advertisement
Table of Contents
Related Manuals for UniStrong UT50
Summary of Contents for UniStrong UT50
- Page 1 UT50 Fully Rugged Windows Tablet Quick Start Guide Unpacking 1. One UT50 Fully Rugged Windows Tablet Unit 2. Two Battery Packs 3. One AC Adapter 4. Power Cord (US/UK) 5. One Digitizer Pen 6. One Hand Strap NOTE: This package does not include headset.
- Page 2 Red blink every 2 seconds----------Battery B capacity is below 10% Red blink every 4 seconds----------Battery B operating temperature is beyond scope, please shut down UT50 immediately and wait the temperature recovery between -20⁰C and 55⁰C. G: Keys Power----------------------Power on or Shutdown UT50...
- Page 3 L: Expansion 1, RJ45 LAN default M: USB3.0 port N: DC slot O: Kensington lock P: Mounting slot Q: 35pin Expansion Bus Connector A: Fingerprint B: Hand Strap Mounting C: Battery A Locking Latch D: Ventilation Holes (Intake) E: Ventilation Holes (Exhaust) F: Dust Cover G: Nameplate H: Nano SIM Card and MicroSD Card Slot...
- Page 4 R: Battery B Locking Latch Installing Nano SIM and MicroSD Cards ●Remove Battery A and you can see two logos in the battery compartment. The left slot is for MicroSD card and the right slot is for Nano SIM card. ●You can use a T6 screwdriver to remove the two screws below the nameplate.
- Page 5 Installing Battery Packs Turn over the computer and insert the battery packs into the battery compartments to a secured seated position.
- Page 6 ●Ensure no foreign objects are under the computer. ●Ensure that the battery locking latch is in locked position. Otherwise, the battery packs may drop during operation. ●Do not touch the terminals of the battery packs and computer. Doing so may cause damage or dirty the terminals and result in computer or battery malfunction.
-
Page 8: Installing Hand Strap
Note: There is a button and four LEDs on the battery. The LEDs will indicate battery capacity when you give the button a short press. If there is no LED light, it indicates no power in battery. If there is one LED light, it indicates very low power in battery. If there are two LED lights, it indicates power is below 50%. -
Page 10: Digitizer Pen
Digitizer Pen... -
Page 11: First-Time Power On
Do not press repeatedly or hold for more than four seconds. ③Entering/Exiting Sleep mode When UT50 is in power on mode, press the power button once. The display will be off and power LED will start blinking. The system enters into sleep mode. -
Page 12: Product Safety Warnings
You can shut down UT50 using the Start menu of Windows. [Start]->[Power]->[Shut down] UT50 will display the power off screen and power LED will be off after a few seconds. The system will shut down completely. PRODUCT SAFETY WARNINGS Use responsibly. Read all instructions and safety information before use to avoid injury. The maximum operating ambient temperature of the equipment is 55°... - Page 13 NOTICE: The SAR limit of Europe is 2.0 W/kg. Device types UT50 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use on the body is 0.675W/kg This device was tested for typical body - worn operations with the back of...
-
Page 14: Sar Information
This device complies with Part 22 & 24 and Part 27 of the FCC Rules. SAR INFORMATION The SAR limit of FCC and ISED is 1.6 W/kg averaged over one gram of tissue. Device types UT50 ( FCC ID:2AOPD-UT50 and IC: 11546A-UT50 ) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use on the body is 1.248 W/kg. - Page 15 NOTICE: Changes or modifications made to this equipment not expressly approved by Shenzhen UniStrong Science & Technology Co.,Ltd. may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.