switel TC 30 Manual

TC 30 - Desktop telephone
1. Unpacking
The package contains:
• Desktop phone TC 30
• Handset
• Coiled handset cord
• Telephone line cord
• User guide
Keep the packing
material for later use.
Keep your sales receipt,
which is your guarantee.
In the case of technical problems,
1. LCD screen
you can contact our hotline 2. Ringer light indication
3. M1, M2, M3 Memory buttons
service, Tel. 0900 00 1675 within
4. Scroll up & down buttons
Switzerland (Costs for call from
5. Deelete button
Swisscom landline at time of going
6. Set/Store button
to print: CHF 2.60/min). In the case
7. Memory button
of claims under the terms of guarantee,
8. Last Number Redial button
contact your sales outlet. There is a
9. Speakerphone button
2 year period of guarantee.
10. Mute button
11. R (Recall) button
12. Pause button
IMPORTANT NOTE
The TC 30 requires 2 x 1.5 V AAA size Alkaline batteries installed
into the battery compartment before use. The caller display will
not work without batteries installed.
2. Installation
Installation location
• The telephone should be placed on a level surface not too close to other electrical
equipment to avoid mutual influence.
• Prevent excessive exposure to smoke, dust, vibration, chemicals, moisture, heat and
direct sunlight.
• Do not use the handset in potentially explosive areas.
Plug the coiled handset cord into the handset.
Plug the other end into the jack on the left side
of the base unit.
Place the handset on the base unit.
Always use the
telephone line
cord supplied with
Plug the telephone line cord's free end
the phone. Other
into a modular wall jack. Plug the other
telephone line
end into the jack on the rear side of the
cords may not
base unit
work!
Lift the handset and check for dial tone
to modular wall jack
in the earpiece.
Ringer high/low switch
Installing (or replacing) the batteries
IMPORTANT! Before removing the battery compartment cover, always make sure,
that the base unit is disconnected from the telephone line.
Install two pieces of Alkaline AAA batteries into the compartment and place back the cover
before use.
Note: 1. Please do not use rechargeable batteries in this phone.
2. Batteries are not included.
3. The battery lifetime is typically about 6 months.
When the batteries are getting weak,
they will become totally discharged and the display screen will not work.
1
2
3
4
5
6
7
8
9
3. Desk / Wall mounting instruction
10
Desk mount
11
12
Wall mount
Make sure the plugs
click into place.
will appear in the display screen. If you do not replace the batteries,
SIZE AAA SIZE AAA
To place the TC 30 on a desk, connect the stand to the
bottom of the phone in the slots near the rear of the base
as shown below.
stand
rigid clips flexible clips
Insert the rigid clips of the stand into the slots on the bottom of
the phone (near the rear of the base). Press down firmly until
the flexible clips click into place.
To remove the stand, (1) pinch the flexible clips, (2) pull back
the stand, and then (3) slide up and forward as shown below.
To place the TC 30 on a wall, connect the stand to the
bottom of the phone in the slots near the front of the base
as shown below.
Insert the rigid clips of the stand into the slots on the bottom of
the phone (near the front of the base). Press down firmly until
the flexible clips click into place.
To remove the stand, (1) pinch the flexible clips, (2) pull back
the stand, and then (3) slide up and forward as shown below.
n d 08453459677
0 3
n at o n e .co m /
o n lin e
Mark two points on the wall that are 92 mm apart to lay the
fixing centers as shown below.
Note: The base unit does not require batteries, but
without batteries the display will not work.
Rasthaken Rasthaken parking hook
Aussparung Aussparung parking recess
Rotate
BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two
screws (supplied with the unit) at the marked locations, leaving approx. 7 mm between
the wall and the screw head.
Hang the base unit on the screws using the wall mount slots.
You may need to remove the telephone from the wall and tighten the screws so that
the unit is securely fixed and does not wobble. Place the handset on the cradle with
the parking hook in the cradle arranged to fit in the parking recess under the earpiece.
4. Setting up the phone
Press the SET/STO button to enter the menu and then use  and  to cycle through the
following options:
• SET 1 DATE • SET 2 LCD • SET 3 FLASH
Note: The system will time out if you leave more than 8 seconds between key presses.
Set Date/Time You will need to set time and date so that it will be shown
correctly in the display. It is also used for showing the date and
time of incoming calls in the caller list.
1
In standby mode, press SET/STO.
The display shows SET 1 DATE.
2 Press SET/STO.
The year is flashing.
Press  and  to set the year.
3
4 Press SET/STO .
The month is flashing.
Press  and  to set the month.
5
6
Press SET/STO .
The day is flashing.
7 Press  and  to set the day.
8
Press SET/STO .
The hours are flashing.
Press  and  to set the hours.
9
10 Press SET/STO .
The minutes are flashing.
11
Press  and  to set the minutes.
12
Press SET/STO .
The display shows SET 2 LCD. Continue programming or
press DELETE to return to standby mode.
In standby mode, press SET/STO.
1
Set LCD
The display shows SET 1 DATE.
contrast
Select SET 2 DISPLAY using  or .
2
3 Press SET/STO .
4
Adjust the contrast using  or .
5
Press SET/STO .
The display shows SET 3 FLASH. Continue programming or
press DELETE to return to standby mode.