Perfomance Tool M660 Owner's Manual

REPLACEMENT PARTS
NO. DESCRIPTION QTY NO. DESCRIPTION
1 Cap Screw 1 18 Washer
2 O-Ring 1 19 Washer
3 O-Ring 1 20 Screw
4 Fluid Controller 1 21 Washer
5 Spring 1 22 Valve
6 Pin 1 23 Valve Sleeve
7 O-Ring 1 24 Valve Body
8 O-Ring 1 25 Bushing
9 Connector 1 26 Washer
10 Screw 1 27 Cylinder
11 Gasket 1 28 Washer
12 Trigger Pin 4 29 Front Bumper
13 Stem 3 30 Piston Rod
14 Spring 3 31 Rear Bumper
15 Pin 1 32 Housing
16 Trigger 1 33 Sleeve
17 Cylinder 1 34 Screw
TROUBLESHOOTING
INSuFFICIENT POWER:
Probable Cause Solution
Dirty or clogged air passages . . . . . . . . . . . . . . . . . .Flush and lubricate tool, drain air tank and supply line
Insufficient air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Increase line pressure, Make sure compressor
matches tool's air pressure and consumption needs
Air leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use PTFE tape at all fittings and joints . Check tool for
worn or damaged O-rings & seals .
Worn/damaged wear & tear parts . . . . . . . . . . . .Replace as necessary .
Tool matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Be sure you are using a tool suited for the torque
requirements of the job at hand .
QTY NO. DESCRIPTION QTY
1 35 Screw 2
2 36 Cover 1
1 37 Screw 2
2 38 Bushing 2
1 39 Washer 2
1 40 Plate 2
4 41 Spring 1
1 42 Guide Plate 1
1 43 Set Screw 2
1 44 Set Screw 2
1 45 Blade Chuck 1
2 46 Wrench, 2 mm 1
1 47 Wrench, 4 mm 1
1 48 Work Guide (Short) 1
1 48 Work Guide (Long) 1
1 49 Blade 2
2
Reciprocating Air Saw
Stock Number M660
OWNER'S MANUAL

SPECIFICATIONS:

Cutting Capacity (GA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Average air consumption (C .F .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Free speed (R .P .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,000
Air inlet (N .P .T .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4
Hose size (I .D .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8 in .
Length (IN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 .25
Weight (LBS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .4
Specifications are subject to change without notice .
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL . FAILURE TO DO SO
MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE
AND WILL VOID WARRANTY .