Download Print this page

E-SCS PBR-15L User & Installation Manual

Full range input voltage retro-reflective photobeam detector

Advertisement

Quick Links

6.RESPONSE TIME
Adjust response time as follows.The unit does not detect the passing object faster than the response time set.
If the response time is set longer, the unit does not detect human beings.
Adjust to a little longer response time in a site where large passing objects, newspaper or carton box may move.
A
B
A
C
Fast running
7.TROUBLESHOOTING
Trouble
Possible Origin(s)
Incorrectly wired and/or insufficient voltage
Sensor LED does not light.
Sensor LED never lights up
a. Insufficient voltage
when the beam is interrupted.
b. Beam reflected away from receiver
c. Beams not simultaneously interrupted.
Beams interrupted and LED
Alarm tigger cable may be cut,or the relay
lights, but no alarm tigger.
contact stuck due to overloading.
Alarm LED continuously lit.
a. Lenses out of alignment.
b. Beam are blocked.
c. Cover is foggy or dirty.
Alarm tigger becomes erratic
Lenses out of alignment.
in bad weather.
Frequent false triggers from
a. Too sensitive.
leaves, bird, etc.
b. Bad location.
8.SPECIFICATIONS
PBR-15L
Light On: Normally Close Relay Output
Model Number
Dark On: Normally Open Relay Output
PBR-15D
PBR-15L
Beam Aligned: 90mA / Beam Broken: 70mA
Current Drain
Beam Aligned: 70mA / Beam Broken: 90mA
PBR-15D
Input Volt.
AC/DC 12~250V
Infrared Led
Red infrared led element/940 nm
Detection Method
Retro-Reflective
Contact capacity
N.O./N.C. Relay Output, 0.5A@120V (min. 1 sec.)
Response time
50~700 msec.
Delay time of relay
1,000 msec
Sensing range
15 meters
Volt. Output
1~6V
Led indicators for
Yellow led Off: Beam aligned / Yellow led On: Beam broken
Yellow led flash: Beam alignment signal weak (Re-align)
beam alignment
& Power
Green led On: Power On
Wirign connection
Terminal block/Cable gland (IP-66)
Ingress Protection
IP-55
Environment/Stroage Temp.
-13 F ~ 131 F (-25 C ~ 55 C)
Alignment angle
Horizontal:
90 / Vertical:
5
Sensor: 0.41 kgs
Weight
Reflector with Hood: 0.25 kgs
Sensor: 182(L)
80.4(W)
91(D)mm
Dimensions
Reflector with Hood: 182(L)
80.4(W)
91(D)mm
B
C
Normal walking
Slow walking
Remedy(s)
Ensure the power supply to the sensor is
10 to 30 VDC.
a. Double-check the voltage.
b. Clean the cover.
c. Check overall installation.
Check the continuity of the wiring between the
sensor and the alarm.
a. Realign the lenses.
b. Remove any obstacles.
c. Clean the cover.
Check overall system installation. If still erratic,
realign the lenses.
a. Reduce the response time.
b. Change the sensor and/or location.
9.EXTERNAL DIMENSIONS
Unit: mm
80.4
91
91
80.4
4
Full Range Input Voltage
Full Range Input Voltage
Retro-Reflective Photobeam Detector
Retro-Reflective Photobeam Detector
PBR-15L / PBR-15D
Features:
Retro-Reflective photobeam detector
Full Range input voltage (AC/DC 12~250V)
Red infrared led element
Long sensing range: 15 meters
IP-55 water proof
Hood for sensor & reflector pack
Triple square shape reflector set
Pole mounting bracket included.
Power and beam alignment led indicators included.
1.PARTS DESCRIPTION
[COVER]
[SENSOR]
Terminals
7 7
6 6
2 2
5 5
3 3
4 4
4 4
3 3
5 5
6 6
2 2
Alarm LED
Voltage
Vertical
adjustment
screw
View finder
2.CAUTIONS ON INSTALLATION
Do Not
Remove all abstructions
Avoid strong light from the sun,
(trees,clothes,lines,etc.)
automobile headlights etc.directly
between Sensor and
shining on Sensor/Reflector.
Reflector.
When strong light stays in optical
axis for a long time, it does not
cause malfunction but will affect
the product life.
Expansion of beam
The protection distance(between Sensor
/Reflector)should be placed in the rated range.
Spread of beam
Model
Detection distance
15m(49 ft.)
0.6m(2.0 ft.)
PBR-15
Applications:
Gateopener
Overhead door
Swing gate
INSTALLATION MANUAL
INSTALLATION MANUAL
Sliding door
Parking lot
Window
Terrace
Warehouse
Perimeter protection
Automation control
[REFLECTOR]
Signal LED
Delay time
adjustment
knob
Horizontal
adjustment
Lens
Do not install the unit on places
Do not install the unit on
where it may be splashed by dirty
unsteady surfaces.
water or direct sea spray.
Detection distance
1
Tapping screw:4
Mounting Plate:2

Advertisement

loading

Summary of Contents for E-SCS PBR-15L

  • Page 1 Adjust response time as follows.The unit does not detect the passing object faster than the response time set. If the response time is set longer, the unit does not detect human beings. PBR-15L / PBR-15D Adjust to a little longer response time in a site where large passing objects, newspaper or carton box may move.
  • Page 2 4.INSTALLATION METHOD Position of installation Wall Mount The photoelectric beam lens can be adjusted horizontally (1)Loosen the cover locking screw and remove (2)Pull wire through on the installation site. (4)When exposed wired break knockouts , and vertically . This allows much flexibility in the cover.Loosen the unit setting screw at (2 positions)on the rear of unit,pull (3)Break grommet on mounting plate and...

This manual is also suitable for:

Pbr-15d