1. Manuals
  2. Brands
  3. CHAMPEDAL Manuals
  4. Bicycle
  5. Champ Climber
  6. User manual

CHAMPEDAL Champ Climber User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
ELECTRIC BICYCLE
1. Important Tips
Do not use the electric bicycle before reading the specification carefully and
USER MANUAL
knowing its performance. And never lend it to those who do not know how to
operate and drive.
Frequent starting, braking, climbing, upwind driving, muddy road, overloading
will consume the battery too much and affect the total range. So it is suggested to
avoid the fact all the above when you drive the electric bicycle.
If the storage battery is stopped using for a long time, Make sure to store it before
charged adequately, and it needs to charge again after stored for more than a
month.
It is forbidden to driving when the motor or other electric parts are all into the
water because of the short circuit.
It is forbidden to disassemble or refit the bicycle without authorization; otherwise,
CHAMPEDAL will not take responsibility for the entire fault caused by it.
It is forbidden to discard the useless battery because of the environment
protecting.
1

Advertisement

Table of Contents
loading

Summary of Contents for CHAMPEDAL Champ Climber

  • Page 1 It is forbidden to disassemble or refit the bicycle without authorization; otherwise, CHAMPEDAL will not take responsibility for the entire fault caused by it. It is forbidden to discard the useless battery because of the environment...

  • Page 2: Spare Parts

    2. Spare parts 3. Assembling and adjusting Step 1: Take the bike from the carton and take off all the protecting films and belts. Step 2: Move the stem to the opposite side. 1. Brake lever 16. Disc 2. Grips 17.
  • Page 3 Step 3: Before assembling the wheel inside the front fork. You must make sure the disc Step 5: There is only 1 screw for the fender. Screw it. It is very easy. is inside the disc clips. Otherwise you cannot put the wheel in or will break the disc pads.

  • Page 4: Operation And Adjustment

    4. Checking before riding 5.2 PAS System Make sure that the brakes and the front & rear lights are all working . ◆Introduction of PAS Check the pressure of the tires. PAS system is a pedal assisted sensor that installed in middle axis position. When you Check the display works well or not.
  • Page 5 Adjustment method for brake pads: 5.4 Brake System 1. Loosen the fixed screw and you will see three holes on fixed Brake system is the most important for your safety driving, so it is necessary to check base; the brake system carefully before driving. 2.
  • Page 6 and the right one controls the rear transmission. 5.7 Battery ﹡If there the speed of the bicycle is 6,7,8 or 9. That Installing and removing the battery means there is only one plate for the crankset. So Remove the battery: turn off the lock located on the battery to the last level. Pull out the there is only a right shift to control the speed.
  • Page 7 will be able to obtain a new one from your dealer. Turn the battery off. The LED lights will be off. Step 1 Maintenance Plug the charger plug into the socket located on the charger (Pic.A). If you don’t use your bike more than 45 days, store it in a dry place to protect the Step 2 Make sure to make them tight.
  • Page 8 5.8 Lubrication Frequency Component Lubricant How to Lubricate Chain Chain Lube Brush On or Squirt Speed shift Brush On or Squirt Weekly Pulleys Chain Lube Oil Can Derailleurs 3 drops from oil can Brake Calipers 2 drops from oil can Brake Levers Monthly Shift Levers...
  • Page 9 Power control 、 headlight control 、 6Km/h control 、 fix-speed cruise control、 rim size set、5 levels assistance set、max speed set、Automatic dormancy set、back light brightness set、Starting method set、driving method set、assistance sensibility set、 assistance magnet disc type set、voltage set、current-limit of controller set， 3.communication protocol：UART ALL ON DISPLAY（power on within 1S）...

  • Page 10: Throttle Fault

    P05：Assistance level : 0-3levels：1 level 2V，2 level，3V，3 level，4V； 1-5levels: 1 level 2V，2 level，2.5V，3 level，3V， 4 level，3.5V，5 level,4V; P06: Rim size：Unit，inch；precision：0.1； 5. Speed display area Current speed CUR、Max speed MAX、Average speed AVG P07: Number of magnet steel：Range：1-100； Unit MPH, KM/H P08: Speed limit：Range 0-50km/h，50 means no speed limit， The display will calculate the speed according to the rim size and signal data (Motor No signal communication condition（Display controlling）:When hall need to set the magnet quantity ).

  • Page 11: Button Introduction

    P16: ODO set to 0. Long press the top button for 5s. . Button introduction： ， Assistance + 1 1.Short press Buttons will be like this ， Assistance - 1 2.Short press 2.Change to speed display Button using introduction Long press Button operations are short press, long press and combination long press.
  • Page 12 5.Change to multifuction display area at the same time. ，quit setting and save，If you do not press，it will 2. Press Short press 6.Setting parameter quit and save automatic after 10S. Marks： Because of the updating of the products, there may be some difference between the product you get and the manual.

  • Page 13: Regular Maintenance

    Maintenance Inspect connectors Your electric bicycle is safe for the environment. Check derailleur adjustment A battery that no longer works must be returned to your dealer so that he may pass it to Check brake adjustment a recycling company. The engine does not require maintenance. Check brake and gear cable adjustment Monthly Check tire abrasion and pressure...

  • Page 14: Warranty

    The motor does 1.Something is wrong 1.Replace the throttle, not work when the with the throttle controller or PAS sensor power is on 2.Bad connecting of the 2.Weld the connecting part power lock and plugs again 3.Something is wrong 3.Adjust the distance between with controller the two parts of the PAS 4.Something is wrong...

Table of Contents