Aeon Labs Aeotek Manual

Aeotec by Aeon Labs LED Bulb.
Aeotec LED Bulb is a low-cost Z-Wave LED module which ®
allows control (on/off/dim) with the use of Z-Wave.
It's a bulb has a Smart RGB LED, which can be used to add
colour to your home. The bulb has 5 main colour channels
available for you to adjust: Red, Green, Blue, Warm White
and Cold White. You can configure its colour according to your
LED BULB
favour.
The LED Bulb is also a security Z-wave device and supports
the Over The Air (OTA) feature for the product's firmware
View the expanded manual:
http://aeotec.com/support upgrade.
Familiarize yourself with your LED Bulb.
ADDED WEIGHT OF THE DEVICE MAY CAUSE
INSTABILITY OF A FREE-STANDING PORTABLE
LUMINAIRE.
THIS DEVICE IS NOT INTENDED FOR USE WITH
EMERGENCY EXITS OR NOT FOR EMERGENCY
LIGHTING.
SUITABLE FOR USE IN ENCLOSED LUMINAIRES.
Quick start. If you're using a Z-Stick:
Getting your LED Bulb up and running is as simple as
plugging it into a wall socket and linking it to your existing
Z-Wave network. The following instructions tell you how to
link your LED Bulb to your Z-Wave network using an Aeotec
by Aeon Labs' Z-Stick or Minimote controller. If you are using
other products as your main Z-Wave controller, such as a 1. Decide on where you want your LED Bulb to be placed and
Z-Wave gateway, please refer to the part of their respective plug it in to a wall outlet. Its RGB LED will be active with a
section of their instruction manual that tell you how to add new colourful gradient.
devices to your network. 2. If your Z-Stick is plugged into a gateway or a computer,
unplug it.
3. Take your Z-Stick to your LED Bulb.
4. Press the Action Button on your Z-Stick.
5. Press the wall switch of LED Bulb to turn it off and then
Wall Switch press the wall switch again to turn it on.
6. If LED Bulb has been successfully linked to your Z-Wave
network, its warm white LED will be solid. If the linking was
unsuccessful, the LED Bulb will continue to be active with a
colourful gradient.
7. Press the Action Button on the Z-Stick to take it out of
installation mode and return it to your gateway or computer.
If you're using a Minimote: With your LED Bulb now working as a part of your smart
home, you'll be able to configure it to indicate different
colours from your home control software via setting the RGB
value. Please refer to your software's user guide for precise
instructions on configuring your LED Bulb to your needs.
You're able to change your LED Bulb's colour manually. After
the LED Bulb is included into your network, switching the
LED Bulb on and off 2 times before the Power Outage LED
is turned off via wall switch will change the colour to the next
1. Decide on where you want your LED Bulb to be placed and
(Warm white, Cold white, Red, Green or Blue).
plug it in to a wall socket. Its RGB LED will be active with a
Note:
colourful gradient.
2. Take your Minimote to your LED Bulb. 1. The Power Outage LED is a small red LED in the Bulb,
which is used to indicate the power outage state of the LED
3. Press the Include button on your Minimote.
Bulb. When the LED Bulb is switched off by the wall switch, it
4. Press the wall switch of LED Bulb to turn it off and then
press the wall switch again to turn it on. will keep solid with red light for 1.2 second and then be turned
off automatically.
5. If LED Bulb has been successfully linked to your Z-Wave
2. The wall switch needs to be left in the "On" position in
network, its warm white LED will be solid. If the linking was
unsuccessful, and the LED Bulb will continue to be active order for the bulb to function properly in the Z-Wave network.
This functionality would include being an active member of
with a colourful gradient.
the routing tables, repeating the Z-Wave RF commands and
6. Press any button on your Minimote to take it out of
installation mode. being controlled remotely.
Removing your LED Bulb from a Z-Wave network. times before the Power Outage LED is turned off.
5. If your LED Bulb has been successfully removed from
Your LED Bulb can be removed from your Z-Wave network
your network, Its RGB LED will be active with a colourful
at any time. You'll need to use your Z-Wave network's main
gradient. If the removal was unsuccessful, the RGB LED
controller, and to do this, and the following instructions will tell
will be solid.
you how using the Aeotec by Aeon Labs' Z-Stick or Minimote
6. Press the Action Button on the Z-Stick to take it out of
controller. If you are using other products as your main Z-Wave
removal mode.
controller, please refer to the part of their respective manuals
that tells you how remove devices from your network. If you're using a Minimote:
If you're using a Z-Stick:
1. If your Z-Stick is plugged into a gateway or a computer,
unplug it. 1. Take your Minimote to your LED Bulb.
2. Take your Z-Stick to your LED Bulb. 2. Press the Remove Button on your Minimote.
3. Press the wall switch of LED Bulb to turn off and then press
3. Press the Action Button on your Z-Stick.
4. Press the wall switch of LED Bulb to turn off and then press the wall switch again to turn on it, repeat the operation 3
the wall switch again to turn on it, repeat the operation 3 times before the Power Outage LED is turned off.