B.E.G. LUXOMAT PD1-M-2C Installation And Operating Instruction Manual

LUXOMAT
B.E.G.
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD1-M-2C/-S-SM/-FC/-FM
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec-
trical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
2c. Installation of the LUXOMAT
®
PD1-M-2C/-S-FM
The detector can
be installed in
conventional inlet-
sockets mounted
on the ceiling.
The assembly
plate enclosed
must be stripped
off prior to instal-
lation and secured
to the ceiling
using 4 screws
and ensuring that
it is not laterally
transposed.
Having connected up the cables in ac-
cordance with regulations, the detector
can be placed in position as shown in
the drawing opposite and, applying
a little pressure, can then be locked
into position with the assistance of the
spring clips.
Option:
IR-PD
max
Wall bracket for remote
control IR-PD
ON
OFF
max
ON
IR-PD-Mini
OFF
®
2a. Installation of the LUXOMAT ®
For surface-mounting, an inwall sensor unit is combined with a surface-mounted
receptacle as a housing base.
Before mounting the base, the enclosed mounting plate must be mounted true to
side, i.e. the writing must be legible.
Now fix the base on ceiling or wall, but first put the cable through one of the
cable openings provided. The detector must be mounted on a flat, solid surface.
Next prepare the sensor part by screwing in both fixing screws, then connect the
cable as per the wiring diagram.
6 mm
3. Putting into operation / Settings
120 60 50 Self test cycle
A
40
The product enters an initial 60-second self-test cycle, when
30
15 the supply is first connected. The occupancy detector is ready
120 60 50 5
10
A
for operation.
40
30
15 Follow-up time for light control
16 10 5 10
5
The time can be set infinitely variably at between
2
15 seconds and 16 minutes.
1
TEST 30
15
16 10
Symbol : Impulse < 1sec.
5
2
Symbol TEST : Test mode (Every movement switches on the
1
TEST 2000
30 light for a period of 1 second, switching it off for a period of
15
1200
2 seconds after that regardless of the level of brightness.)
600
200
Twilight-switch for light control (relay 1)
40 2000
1200
The switch-on value for the light can be set at between 10
600
and 2000 Lux. Using the rotary control, the luminance set
200
40
points can be set as desired.
Symbol : Night-time operation
Symbol : Daytime / Night-time operation
Follow-up time for appliance-control
120 60 50
A
The time can be set infinitely variably at between 5 minutes
40
30
and 120 minutes. There is a period of delay prior to switch-on
15
5
10
of between 5 - 10 minutes for times set in excess of 15 minutes.
Symbol : Impulse = 1sec.
16 10
Symbol A : Alarm impulse = 1sec.
5
2
1
TEST
30
15
Unlocking device
2000
1200
600
��
Luminance set point
��� ����
200
���
40
Automatic reading in the current light value
as new luminance set point
R1
Individual light value 2 - 2500 Lux
��
Follow-up time (relay and channel 1)
��� ��
15 sec. up to 30 min.
���
Impulse function (relay and channel 1)
1sec. ON, 9 sec. OFF
Time setting (relay and channel 2)
�
��� ���
5 min. up to 120 min.
���
Impulse function (relay and channel 2)
R2
The voltage-free contact is closed for a period of 2 seconds.
This is followed by a period of idle time of 8 seconds' duration.
50
1500
Lux
Lux
A Alarm impulse program for appliance control (relay 2)
3
The relay will not close until at least three movements have been
registered over a period of 10 seconds (impulse = 1 second).
Preset / user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (flashing),
Fully automatic: red LED on for approx. 3 sec.
50
1500
Resetting when open
Lux Lux
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
Lock device
PD1-M-2C/PD1-S
PD1-M-2C/-S-SM
Now insert the sensor part and check for matching positioning
of the two markings.
Press beyond the spring housing pressure so that the sensor
part firmly locks in place.
Now turn the sensor part counter-clockwise for about 10° to
the stop.
max
ON
OFF
2b. Installation of the LUXOMAT
PD1-M-2C/-S-FC
Having connected up the cables in accor dance
with regulations, the detector is inserted into
the opening as shown in the drawing opposite
and fixed into position with the assistance of the
spring clips.
4. PD1-M-2C: Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PD
®
120 60 50
A
40
30
15
5 1. Check Battery:
10
open battery compartment by pressing the plastic
120 60 50
16 10
A springs together and removing the battery-holder.
5
40
2
30
1
15
5 10 TEST
30
15
2. IMPORTANT
1 2
Please pay attention, that the setting is Potentio-
16 10
2000
5
1200 meter 1 at "TEST" and Potentiometer 2 not at
2
600
1
"SUN". All values which have been programmed
TEST 200
30
15
40
120 60 50 using the remote control will be deleted in the
A
40
event of power failure in the position "TEST/
30
2000
15
SUN". Please switch Potentiometer 2 over to
5 10 1200
600
1 2
"MOON" or any other value.
200
40
2000
16 10
5
1200
2
600
1
200
TEST 30
15
40
Caution:
Settings with remote control supersede the settings
2000
1200
by courtesy of potentiometers.
600
200
40
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
during the period of 5 seconds after pressing the "lock"
button. This status will only permit actuating the function
"Light on/Light off".
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
50 1500
4. Apply current
Lux
Lux
5. Open detector
Light on/ off
The light will remain switched on/ off for as long as move-
ments are detected in the areas of coverage. Once the last
movement has been detected, the light will remain on for
the duration of the follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).
GB
®
The detector has
been designed and
developed specifically
for installation in sus-
pended ceilings.
A circular opening of
diameter 68 – 70 mm
must be produced in
the ceiling.