Summary of Contents for Cinegears Ghost-Eye SH700M
- Page 1 GHOST EYE WIRELESS HDMI/SDI VIDEO TRANSMISSION SYSTEM 1000M GHOST EYE MANUAL BOOK © 2017 Cine Gears INC. All Rights Reserved.
- Page 2 Trademarks Ghost-Eye Wireless Video Transmission SystemsTM are trademarks of Cine Gears Inc. Web Interface. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Cine Gears Inc. reserves the right to make changes to the products described in this docu- ment without notice.
- Page 3 Information to the user The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equip- ment.
-
Page 4: Table Of Contents
Contents Cautions Ghost Eye Wireless Video Transmission Systems Specifications Transmitter Receiver Installation Transmitter Receiver LCD Screen User Manual Troubleshooting Disclaimers About Cinegears © 2017 Cine Gears INC. All Rights Reserved. -
Page 5: Cautions
Cautions Warning Please read this user introduction manual to become familiar with the features of the Ghost-Eye series products before operation. Failure to operate the product correctly can result in disturbing other film equipment on set. This product is not intended for use by children without direct adult supervision. -
Page 6: Ghost Eye Wireless Video Transmission Systems
Ghost Eye HD Wireless Video Transmission Systems Here at Cinegears, we supply some of the best wireless HD video transmitters and receivers available. During the development of the Ghost Eye line of products, we subjected our prototypes to rigorous testing on set with professional film crews, and took customer feedback and suggestions into serious consideration. -
Page 7: Specifications
Specifications Specification ITEM Specification Frequency 5.1-5.9(GHz) Bandwidth 40MHz 1080p 23.98/24/25/30/50/60 1080i 50/59.94/60 Video Formats 720p 50/59.94/60 Supported 576p 576i 480p 480i Audio Formats PCM, DTS-HD, Dolby TrueHD Supported Time Code SMPTE-12M Transmission range 1000m(MAX) Transmitter Antenna External Antenna x 2 pcs Transmission power 18dbm HDMI Input;... -
Page 8: Transmitter
Transmitter Structure & Interface Transmitter SH700M © 2017 Cine Gears INC. All Rights Reserved. - Page 9 Transmitter Structure LCD Screen Display the information about the Channel, signal input, capacity, fan control. Select the correct Channel. DOWN Select the correct Channel. MENU Unlock the screen and confirm the selection. Power ON/OFF Power ON/OFF SDI IN Connect the HD camcorder which support 3G-SDI, HD-SDI SDI OUT (Loop) Connect to the HD digital monitor which support 3G-SDI, HD-SDI HDMI IN...
-
Page 10: Receiver
Receiver Structure & Interface Receiver SH700M © 2017 Cine Gears INC. All Rights Reserved. - Page 11 Receiver Structure Antenna socket SMA socket to connect the antennas. LCD Screen Display the information about the Channel, signal input, capacity, signal status. Menu Unlock the screen and confirm the selection. Left Select the correct Channel. Right Select the correct Channel. BAT-out Btap battery power supply.
-
Page 12: Installation
Installation Installation For Transmitter 1.Fix the antennas to the transmitter, and arrange them to be right angle as figured below 2.Connect the transmitter to the power supply via the certain power cable or SONY F970/F550 battery. Connect the SDI/HDMI cable to the HD video source. - Page 13 Installation 3.Turn ON the power supply and make sure the transmitter start to work. 4.Long press the “MENU” button to unlock the screen and then press “+” or “-” button to select the wireless channel that corresponding to the Receiver, then press the “MENU” button to confirm. When the video signal is normally transferred, the LCD screen will dis- play “video”.
-
Page 14: Receiver
Installation For Receiver 1.Fix on the antennas to the Receiver, and arrange them to be right angle as figured below. 2.Connect the Receiver to the power supply via the certain power cable or V-mount battery. Connect the SDI/HDMI cable to the TV/Monitor. ©... - Page 15 Installation 3.Turn ON the power supply and make sure the receiver start to work. 4.Long press the “MENU” button to unlock the screen and then press “LEFT” or “RIGHT” button to select the wireless channel that correspond- ing to the Transmitter, then press the “MENU” button for confirm. When the networking is normally connected, the LCD Screen will display signal status.
-
Page 16: Lcd Screen
Installation SH700M Transmitter LCD Screen Screen Lock/Unlock : The screen will be always locked unless long press the MENU button to unlock. Power Info : Display the current power supply status. Channel NO. : Display the current Channel NO. of device. Video Connect : Video means the video signal is OK. - Page 17 Installation SH700M Receiver LCD Screen Screen Lock/Unlock : The screen will be always locked unless long press the MENU button to unlock. Power Info : Display the current power supply status. Channel NO. : Display the current Channel NO. of device. RSSI : Received signal strength indication.
-
Page 18: User Manual
User Manual Supports full PSF resolutions 25PFS in = 25PFS out 23.98P in = 23.98P out 29.97PSF in = 29.97PSF out 24P in = 24P out 30PSF in = 30PSF out 25P in = 25P out 50i in = 50i out 29.97P in = 29.97P out 59.94i in = 59.94i out 30P in = 30P out... - Page 19 User Manual Optimal The transmitter and receiver are both in vertical direction The antennas at both sides are in vertical direction The transmitter and the receiver are facing directly Line of sight Transmission range: 500m Average The transmitter and receiver are both in vertical direction The antennas at both sides are in vertical direction TX and RX Facing side Line of sight transmission range: 300m...
- Page 20 User Manual It is recommended that transmitter antennas shall be changed to cross-facing to the receiver, shown as below: Worst The transmitter and the antennas are in horizontal direction The receiver and antennas are in vertical direction Transmission range : 150m This installation is not recommended！...
-
Page 21: Troubleshooting
Troubleshooting Trouble Shooting TROUBLES&POSSIBLE REASONS: SOLUTON: Displaying “Waiting for connection…” for a long time Transmitter is not powered up. Power on the transmitter. Transmitter or receiver is not placed correctly. Place the TX or RX correctly. The transmitter and receiver are too far away. Move the receiver closer to the transmitter. -
Page 22: Disclaimers
Disclaimers FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 23 You agree that you are responsible for your own conduct and any content created while using CINEGEARS products, and for any consequence thereof. You agree to use this product only for purposes that are proper and in accordance with local regulations, terms and any applicable polices and guidelines.
-
Page 24: About Cinegears
About Cinegears Cine Gears Inc. is an industry leading company that designs and manufactures digital wireless follow focus systems, lens control systems, camera motion control systems and accessories for film and broadcast industry. As a big believer in the power of creativity and ideas, we designed the Pegasus cablecam, the wireless motor drive that integrated a built in wireless transmitter, and the wireless finger wheel controller.
Need help?
Do you have a question about the Ghost-Eye SH700M and is the answer not in the manual?
Questions and answers