Advertisement
Quick Links
Art No.: MCT225-P3-GB
SIZE: (W)440mm x (H)99mm(單色雙面黑白印刷)
SO_1132_11N
1. INTRODUCTION
2. GETTING PREPARED
WARNING
The computer has two menus: bike and cadence. The icone
● Please dispose of used batteries according to local
BIKE is displayed in the bottom field when the bike menu is
activated, while icon CAD is displayed in the bottom field
regulations.
when the cadence menu is activated.
● Keep batteries and accessories away from children.
Press the B button to toggle between the two menus.
Press the A button to toggle through various sub-features of
each menu.
2. FEATURES
● Current Speed (0-99.9 km/h or mi/h)
● Average Speed (0-99.9 km/h or mi/h)
● Max. Speed (0-99.9 km/h or mi/hr)
● Trip Distance (Up To 999.99 km or mi)
Button A
● Auto Trip Timer ( 9 : 59 : 59)
● Service Reminder
● Speed Comparator
● Speed Tendency
● Odometer Save Function
● Total Distance
● Digital Clock
● 12/ 24 Hour Selectable
● KM/ M Selectable
● Current Cadence
● Average Cadence
● Maximum Cadence
● Auto Power Off
● Auto Wake Up
● Temperature (-10°C to 50°C)
● Selection (°C/°F)
● Calories Burn (CAL)
● Fat Burnt (FAT)
● EL Backlight
● Autoscan (SCAN)
ATTENTION !! Refer to the appendix for installation reference.
5. OPERATING THE COMPUTER
THE BIKE MODE:
CLOCK
It shows the current time.
MAXIMUM SPEED (MXS)
Hold the A button to reset the clock.
Press the B button to adjust the value and
It measures the maximum speed reached.
confirm with the A button.
AVERAGE SPEED (AVS)
ODO (TOTODO-1)
It measures average speed.
It measures the distance accumulated
for bike 1.
TEMPERATURE (TEMP)
It measures the current temperature.
ODOMETER SAVE FUNCTION
Hold the A button to change the temperature
It allows you to re-input odometer for bike
1 battery replacement. Hold the
unit, if needed. Press the B button to select
to re-input the odometer. Press the B
and confirm with the A button.
button to adjust the wheel size factor of
A button
bike 1, if needed. Confirm with A button.
CALORIES BURNED (CAL)
It measures the calories burned.
TRIP DISTANCE (DST)
It measures the distance traveled at each ride.
FAT BURNT (FAT)
Reset function
It measures fat burned (in grams).
Hold the A button for 3 seconds to reset the Trip distance
and the Trip Timer.
SCAN
TRIP TIME (TM)
It sets the computer to cycle through all
It measures the time of each ride.
features automatically while you ride.
441mm
THE BIKE
WHEEL SIZE FACTOR
The wheel size factor is the distance the wheel turns in one
revolution in millimeters. It is determined by the following
formula: Wheel diameter (mm) X3.1416
For quick reference, you may use the wheel size factor chart below.
Current Cadence
Current Speed
Sub-Feature
Button B
Fig. 1
Fig. 2
Distance in millimeters
in one revolution
For most accurate value, please follow the steps below:
1. Start by inflating the tire with proper pressure
2. Facing the tire valve to the ground, mark a spot on the
ground (right below the valve)
3. With the rider's weight on the bike, roll one full rotation in a
straight line (so roll until the valve faces the ground again)
4. Measure the distance in millimeters.This value is your wheel
size factor.
SERVICE REMINDER
It automatically tracks distance traveled and
reminds you to service your bike according to
the distance entered.
Release
When the preset distance is reached, SERVICE
will be displayed at the bottom field and
will be flashing.
Press button A to ignore this reminder.
SPEED TENDENCY
Notice the
in the upper left hand corner
of the middle display field. The icon is
animated to spin when the wheel sensor is
properly functioning and when you start
your ride. It will appear to spin fast to
indicate acceleration and appear to spin
slow to indicate deceleration.
SPEED COMPARATOR (
/
)
Notice the
/
icon located in the lower
right hand corner of the middle display field.
A
indicates that you are riding faster than
your average speed. A
indicates you are
riding slower than your average speed.
THE CADENCE MODE:
CURRENT CADENCE (CAD)
It shows the current cadence.
MAXIMUM CADENCE (MAX CAD)
It measures the maximum cadence reached.
AVERAGE CADENCE (AVG CAD)
It measures the minimum cadence.
3. GETTING STARTED
SETUP MODE
You can go to the setup mode by either:
a) Inserting the battery (if not installed)
b) Holding both A and B buttons
Press B button to adjust the value and the A button to enter and confirm the setting.
Bike 1 wheel
KM or M
Age input
KG or LB
size factor input
selection
selection
Weight input
12 or 24
Clock setting
Bike 1 service
format selection
reminder setting
C/F selection
Home screen
EL BACKLIGHT (OPTIONAL)
The EL backlight can be turned on either as follows:
1)Holding the RIGHT button for 2 seconds, the EL light will be
SCAN
turned on for 8 seconds and the computer will then go to fast
It sets the computer to cycle through all
scan mode with trip distance, maximum speed, average
features automatically while you ride.
speed and trip timer displayed once.
2)Press once on the LEFT Button, the EL light will be turned
Reset function
on for 4 seconds and the comuter will go to the freeze frame
To reset Maximum Speed, Average Speed, Calories burned,
menory mode as well.
Fat burnt, Maximum Cadence and Average Cadence, go to each
CHANGE OF DIGITAL CODE ID NUMBER
mode and hold A button for 3 seconds.
Whenever you feel there is external interference with your
computer (e.g., 2 similar computers being used close to one
AUTO SLEEP AND WAKING THE COMPUTER
another and at the same time), you can change the digital code
If this computer is left idle for more than 5
ID number to avoid interference as per either of the following
ways:
minutes, it will automatically go to the sleep
A) The Manual Digital Code ID Selection Mode - Immediate
mode (with clock) for battery saving. Press
Change
either button to wake the computer and return
a) Hold the RIGHT button of the computer for 5 seconds until
to the last screen.
the "change of digital code ID number mode" appears on the
display.
LOW BATTERY WARNING OF THE
b) Press the reset button once on the transmitter.
COMPUTER (
)
c) Use the magnet to activate the transmission.
Notice the icon
located in between KM/h
d) The new ID number will thus be registered (e.g., current ID #
and
/
. It indicates low battery of the
03 change to new ID# 04)
computer head.
LOW BATTERY WARNING OF THE
a)
SENSORS
Notice TX LOBAT displayed at the bottom
field. It indicates low battery of either the
Hold the computer's
Showing
speed or the cadence sensor. Press A button
RIGHT button 5 seconds
current ID # 3
to ignore this warning.
B) The Automatic Digital Code ID Selection Mode - Running
AUTO WAKE UP
Change
When there is a signal sending out from the sensor or the belt,
a) Press the reset button once on the transmitter.
this computer can wake up automatically without pressing any
b) Keep on running as usual to activate the transmission.
button. In the first two hours after it turns off, the computer takes
c) The new ID # will register after approximately 1 minute.
no more than 10 seconds to wakes up. After the first two hours,
During the process of the new ID registration, the computer
it takes less than 1 minute for the computer to wake up.
will show no data.
4. OPERATING THE COMPUTER
SCROLLING THROUGH MENUS AND SUB-FEATURES
Press
Button B
CAD mode
Cadence
Max Cadence
Average Cadence
Important Notes
1) Channels 00, 01, 02, 03, and 04 represent BIKE ID number
Channels 05, 06 ,07, 08, and 09 represent CADENCE ID number
Channels 10, 11, 12, 13, and 14 represent HR PULSE ID number
2) CADENCE ID# change: same procedure as for BIKE ID# change
mentioned above.
3) For the PULSE signal ID # change, proceed as below:
a) Remove the battery from the chest strap and insert it again.
b) Hold the RIGHT button of the cyclocomputer for 5 seconds until
the "change of digital code ID number mode" appears on the display.
c) Rub the 2 sides of the strap with 2 fingers. The new signal with new
ID will then be transmitted and registered.
d) You can also remove the battery from the chest strap and insert it
again. Wear the chest strap again. New signal with new ID# will be
transmitted and registered in approximately 1 minute.
CAUTION:
Since the ID number will not be shown on the display, use the above
procedure A) in order to check the current ID#.
Also make sure you are in an interference free area during this ID# change
process in order to avoid abnormal ID# registration.
TROUBLE SHOOTING
No
Improper magnet
Check magnet and sensor
speed or
and sensor
alignment
cadence
alignment
Replace the battery.
reading
Dead battery of
Reset the computer and the
sensor
sensor.
Improper
Interference
Keep the unit away from any
b) and c)
and
source of interference (e.g. CRT
Wrong wheel
abnormal
monitor and wireless devices)
size factor
reading
Reset the computer and the
sensor
(after using the magnet to
Irregular
Ambient
Reset the computer and the sensor
activate the transmission)
reading
temperature
Weak temperature
INSTRUCTION MANUAL
Interference
1010126-1
Art No.: MCT225-P3-GB
Max Scan
CYCLE COMPUTER
Advertisement
