Advertisement
Quick Links
Advertisement
Summary of Contents for Duro 9100SXT
- Page 1 9100SXT Meter Initiated Water Softener OPERATION MANUAL PLEASE NOTE: On page nine of this manual you will find important maintenance procedures for the continued proper operation of your unit. These MUST be performed regularly for your guarantee to remain valid.
- Page 2 Pipe Size = 3/4” • Do not use where water is microbiologically unsafe. • Capacities are based on two tanks of resin. Eg: DT30TM, 9100SXT • The manufacturer reserves the right to make product improvements set at 6lb/cf selt setting would provide 23,000 grains of hardness which may deviate from the specifications and descriptions stated removal for one tank.
- Page 3 Control Operation During Programming The control will only enter the Program Mode with the valve in Service. While in the Program Mode, the control will continue to operate normally, monitoring water usage and keeping all displays up to date. Control programming is stored in memory permanently, eliminating the need for battery back-up power.
-
Page 4: Installation Instructions
Installation Instructions All government codes and regulations governing the installation of these devices must be observed. CAUTION:If the ground from the electrical panel or breaker box to the water meter or underground copper pipe is tied to the copper water lines and these lines are cut during installation of the Noryl bypass valve and/or poly pipe, an approved grounding strap must be used between the two lines that have been cut in order to maintain continuity. - Page 5 Figure 3 4. Attach the bypass valve to the control valve. Connect the inlet and outlet of the water softener to the plumbing in the house. The control valve must not be submitted to temperatures above 71°C (110°F). When sweat fittings are used, to avoid damaging the control valve, solder the threaded copper adapters to the copper pipe and then, using Teflon tape, screw the assembly into the bypass valve.
-
Page 6: Operating Instructions
Operating Instructions Figure 4 The valve has been pre-programmed with factory settings as follows: Regeneration Cycle Step Programming 1. Backwash ........10 minutes 2. Brine Rinse ........60 minutes 3. Rapid Rinse ........10 minutes 4. Brine Refill ........08 minutes – DT30TM 10 minutes – DT40TM 10 minutes –... - Page 7 User Programming Mode Options Abbreviation Parameter Description Day Override The timer’s day override setting THIS IS AN OPTION ONLY. PLEASE DO NOT ADJUST BEFORE CONSULTING AN AUTHORIZED DEALER. Feed Water Hardness The hardness of the inlet water - used to calculate system capacity for metered systems Reserve Capacity The fixed reserve capacity...
- Page 8 Error Codes Note: Error codes appear on the In Service display Error Code Probable Cause Recover and Resetting [Err 0] Drive motor is stalled Unplug the unit from the power source [Err 1] Drive motor is running continuously When power is restored to the unit, the Err _ display code clears.
- Page 9 Manual Regeneration Cycle If you run out of softened water because of inadequate regeneration frequency, inadequate reserve capacity, power failure or unusually high water usage, you can initiate a manual regeneration simply by pressing the extra cycle button. The softener will now automatically complete a regeneration cycle and return to service. If possible, avoid water use during the regeneration cycle.
-
Page 10: Maintenance Instructions
Maintenance Instructions Checking the Salt Level Check the salt level monthly. Remove the lid from the cabinet or brine tank, make sure salt level is always above the brine level (you should not be able to see water). Adding Salt Use only clean salt labeled for water conditioner use, such as crystal, pellet, nugget, button or solar. -
Page 11: Troubleshooting Guide
Trouble Shooting Guide CONDITIONER DELIVERS HARD WATER Bypass valve is open Close bypass valve No salt in brine tank Add salt to brine tank and maintain salt level above water level Injector or screen plugged Replace injectors and screen Insufficient water flowing into brine tank Check brine tank fill time and clean brine line flow tank control if plugged Hot water tank hardness Repeated flushing of the hot water tank is required... - Page 12 Guarantee guarantees that your new water conditioner is built of quality material and workmanship. WaterGroup Companies Inc. When properly installed and maintained, it will give years of trouble free service. Seven Year Complete Parts Guarantee: will replace any part which fails within 84 months from date of manufacture, as indicated by WaterGroup Companies Inc.
Need help?
Do you have a question about the 9100SXT and is the answer not in the manual?
Questions and answers