Page 2
Thank you for buying the ZEPCAM Mobile Video Box. We hope you will enjoy our product as much as we enjoyed creating it. Before starting please check: ● If the product or the packaging is not visibly damaged. ...
Changes Made by Reviewed by 01-Apr-2018 Initial version MT MM 18-Apr-2018 Add appendix A: Supported cameras MT More information and FAQ on: w ww.zepcam.com/support 3 ...
Manage and viewing of video Storage / GPS / HDMI System settings ● Backup /restore ● Update ● Factory reset ● Power settings Appendix A: supported cameras More information and FAQ on: w ww.zepcam.com/support 4 ...
HOW TO USE YOUR PRODUCT The Zepcam Mobile Video Box is a flexible and easy to use solution for wireless video surveillance for IP cameras. The Mobile Video Box comes with integrated back end software. It is an effective way to wirelessly stream and remotely manage surveillance cameras using 3G/4G or ...
Page 6
9. Maintenance button: Push to put MVB into maintenance mode. 10. Reset button. See chapter Reset buttons for explanation 11. Link LED: Indicates Link to Zepcam Video Server. (See table 1.1) 12. Status LED: Indicates power on. (See following table) ...
Page 7
● Short Press (1 beep - status led blinking) : switch from run to maintenance mode. Press again to switch back. ● Press 5 seconds (wait for 2nd beep): Enables the Wifi-Access Point mode in de M2-MVB. More information and FAQ on: w ww.zepcam.com/support 7 ...
Page 8
The Power output is a loop through of the Power input and can be used to power a external device such as a camera. More information and FAQ on: w ww.zepcam.com/support 8 ...
Bare leads power connector Connect the bare leads to a 12-30 Volt power supply Power adapter 230V - 12V More information and FAQ on: w ww.zepcam.com/support 9 ...
You can use the cigaret plug to power the M2-MVB in a car. ANTENNA CONNECTION Recommended to use the M2-MA1 or M2-MA2 multi band dome antenna in combination with your M2-MVB More information and FAQ on: w ww.zepcam.com/support 10 ...
NETWORK CONNECTION The M2-MVB on board web page can be approached via ethernet or via Wifi. You can choose one of the 3 following option to connect and setup your Zepcam MVB Option 1 Connect over a network using DHCP ...
Page 12
Switching between Run and Maintenance mode can be done by using the Maintenance button or on the onboard website go to: System -> Run mode and system -> Maintenance mode. More information and FAQ on: w ww.zepcam.com/support 12 ...
[Note] : The [username], [password] and [ip address] are the username, password and ip address from the IP camera. Make sure the M2-MVB is able to connect to the ip camera’s. More information and FAQ on: w ww.zepcam.com/support 13 ...
M2- MVB to open the camera’s webpage. To change the Port Forwarding settings you can go on the onboard webpage to N etwork ->Advanced S ee Fig 3.3. Fig 3.3 Port forwardings More information and FAQ on: w ww.zepcam.com/support 14 ...
Page 15
You will try to login to the camera on IP address 10.20.30.11 from Fig 3.3 and your logged in to the M2-MVB using the default Wifi IP settings. You can Enter http://10.150.160.1:1081 in you web browser to open the camera’s settings page. More information and FAQ on: w ww.zepcam.com/support 15 ...
NETWORK SETTINGS HOW TO CONFIGURE EACH INTERFACE The M2-MVB contains a Mobile, Wifi and two Ethernet connections. Each network can be used to stream video to the Zepcam Video Server. NETWORK CONNECTION To Change the Mobile Network settings go on the onboard webpage to: ...
Page 17
H ere you can setup 2 dns servers. They are only used when the protocol is set to d ns2: fixed IP. [Note] : dns is necessary when device wants to pair with cloud servers More information and FAQ on: w ww.zepcam.com/support 17 ...
Client mode The wifi client mode can be used to stream Video data to the Zepcam Video Server over Wifi. The steps to connect the M2-MVB to a network are : ● Go on the Onboard webpage to Network ->Wifi ...
Page 19
● The w ifi client m ode can be used to stream Video data to the Zepcam Video Server over Wifi. The steps to connect the M2-MVB to a network are : ● Go on the Onboard webpage to Network ->Wifi ...
Page 20
PRIORITY The M2-MVB will connect to the Zepcam Video Server over the highest interface in the list that is able to reach to the server. All the interfaces under the “Not allowed below this line” will not be used to connect to the Zepcam Video Server. ...
To use the M2-MVB as a mobile hotspot you need to enable the mobile hotspot function at Network → advanced → Mobile Hotspot . You need a server link over the Mobile Network to use the M2-MVB as a Mobile hotspot. More information and FAQ on: w ww.zepcam.com/support 21 ...
Page 22
7. Enter/past the Generated Pairing code in the Registration code field 8. Press pair [Note] : The M2-MVB needs to be able to connect to the Zepcam Video Server to complete te pairing. Be sure the mobile video box can reach the server. ...
MANAGE AND VIEWING OF VIDEOS View live streams Live streaming is only visible in Zepcam Manager in the tab “Live” For more information please consult the Zepcam Manager manual Manage recordings ● From the onboard webpage of the Mobile Video Box, in the tab ...
Page 24
● On the onboard website go to: S ystem → Storage ● In the Format Storage section press F ormat . ● After a while the Storage is formatted. More information and FAQ on: w ww.zepcam.com/support 24 ...
Page 25
HDMI settings you need to go to System -> HDMI display. You can choose between several resolutions. And you can choose to show always camera 1 on the display or the same image as send to the Zepcam Video Server. More information and FAQ on: ...
UPDATE FIRMWARE There are two ways to update the M2-MVB firmware. When the M2-MVB get’s a report from the Zepcam Video Server that there is an update available, it is displayed on the Bottom of the screen. Press Update available to download the firmware. ...
● There are 2 Power thresholds, When the Continuous Voltage is below it’s threshold the M2-MVB will always shutdown itself. The Switched voltage threshold will only operate in combination with the “Switched voltage on” and “Switched voltage off” More information and FAQ on: w ww.zepcam.com/support 27 ...
Page 28
You can Turn off the leds and beeps by going on the onboard webpage to System → Device. Here you can: ● enable/disable the beeps ● enable/disable Stealth mode. this disable the beeps and the leds (this also applies to the ethernet leds) More information and FAQ on: w ww.zepcam.com/support 28 ...
Page 29
M2-MVB POE Axis Q6045 PTZ Camera External Power supply Axis M5525-E PTZ Camera M2-MVB POE Panasonic WV-SC385 PTZ Camera M2-MVB POE SOAR PTZ Camera M2-MVB IO Connector More information and FAQ on: w ww.zepcam.com/support 29 ...