Summary of Contents for Charles Ischi AG AE-1
- Page 1 OPERATING INSTRUCTIONS ABRASION AND FRIABILITY TESTER AE-1 Version 2.06 14.11.2006 Rights reserved for technical changes OME_306511...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page 1. START UP..........................3 2. USER GUIDANCE........................4 3. TECHNICAL DATA......................... 6 4. FINAL ASSEMBLY CONTROL TEST ................. 7 5. SERVICING..........................8 6. TROUBLESHOOTING......................9 7. SPARE PART LIST ....................... 10 8. CE – CONFORMITY DECLARATION................11 9. -
Page 3: Start Up
START UP 1. Operating voltage Before plugging the machine in, check the voltage selector on the rear panel. 2. Mounting the test drums The tester is delivered with power cable and operating manual. The test drums are avaliable as an option in 2 versions: Friability test or abrasion test. The test drums are prevented from rolling by tabs on the inside and a quick release nut on the outside of the shaft. -
Page 4: User Guidance
USER GUIDANCE 2.1. Switch machine on After the machine is switched on the machine version is shown in the display first, then the actual operating parameters: Line 1: Preset rotation speed / PARAM * Line 2: Time or total counts / START # The machine can be operated using preset time or total counts, as desired. - Page 5 2.3. Load test drums By removing the quick release nut either the drum lid or the complete drum can be removed from the machine. The tablets are loaded into the test drum and the drum is held in place on the shaft by means of the quick release nut. The test drum is correctly mounted and closed when the quick release nut snaps into the groove on the shaft.
-
Page 6: Technical Data
TECHNICAL DATA Power connection 200-240V / 50-60Hz Fuses 2x M1A/250V Speed 10 – 99 rpm Preset time 1min – 23h 59min Number of rotations 10 – 999999 r Drums Friability drum Abrasion drum OME_306511... -
Page 7: Final Assembly Control Test
FINAL ASSEMBLY CONTROL TEST Each machine undergoes, as a minimum, a 12-hour final assembly control test prior to delivery. During this test all machine functions are checked. OME_306511... -
Page 8: Servicing
SERVICING The servicing contains a periodical cleaning of the tester. There are no wearing parts. The spare part list you can find under point 7. OME_306511... -
Page 9: Troubleshooting
TROUBLESHOOTING Machine malfunctions should only be repaired by an authorized school trained technician. In the case it is not possible to correct the malfunction, Charles Ischi AG, or the responsible representative should be contacted for repairs. OME_306511... -
Page 10: Spare Part List
SPARE PART LIST Description Art. no. Base plate 310901 Cover 310902 Display complete 310903 Main board 310904 Front foil 310905 Display board 310906 Sensor speed 310907 Sensor rotations 310908 Motor 310909 Axis left 310910 Axis right 310911 Fixing / drum left 310912 Fixing / drum right 310913... -
Page 11: Ce - Conformity Declaration
CE – CONFORMITY DECLARATION Wir / We Charles Ischi AG Langfeldstrasse 26 4528 Zuchwil Schweiz / Switzerland Erklären hiermit, in alleiniger Verantwortung, dass dieses Produkt, Declare sole responsibility for our product, Abriebs- und Friabilitäts -Testgerät Abrasion- and Friability Tester AE-1 Auf die sich diese Erklärung bezieht, die Normen und normativen Dokumente der... -
Page 12: Declaration Of Conformity With Ph-Eur5.0/2005 And Usp29 Nf2006
DECLARATION OF CONFORMITY WITH PH-EUR5.0/2005 AND USP29 NF2006 Wir / We Charles Ischi AG Langfeldstrasse 26 CH-4528 Zuchwil Switzerland Erklären hiermit, in alleiniger Verantwortung, dass dieses Produkt, Declare sole responsibility for our product, Abriebs- und Friabilitäts -Testgerät Abrasion- and Friability Tester... -
Page 13: Drawings
DRAWINGS Drawing no. Machine overview Rear panel OME_306511... - Page 14 OME_306511...
-
Page 15: Technical Information - Install Support 10° Angle
TECHNICAL INFORMATION – Install support 10° angle Machine with angle 10° angle with screw Take out one of these two screws left or Use the screw which we deliver with this right and put on this place the 10° angle. angle, see on the picture in which position you have to fasten the angle.