Advertisement
Introduction
Thanks for choosing the Vision's CT Clamp Bridge of the home automation device. This
TM
module is a Z-Wave
enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave
TM
powered Z-Wave
enabled device acts as a signal repeater and multiple devices result in
more possible transmission routes which helps eliminate "RF dead-sport".
TM
Z-Wave
enabled devices displaying the Z-Wave
regardless of the manufacturer, and ours can also be used in other manufacturer's
TM
Z-Wave
enabled networks. This module will receive the most update energy usage
from CT Clamp, and send to the controller by its signal. This module will also send
dimmer signal to the appliance that attached to this module by receiving Z-Wave
from controller or manually switch. With special design, this module won't interfere the
other power outlet when plug into the AC outlet. This module also acts as repeater
(supporting FLiRS).
Product Description and Specification
* For indoor use *
Specification:
TM
Protocol: Z-Wave
(ZM3102N)
Frequency Range:
908.42MHz (2GIG-Z-BRG1-433)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15
~ 60
(5
~ 140
° C
° C
° F
Operating Voltage: 120V~, 15A, 60Hz
For 2GIG-Z-BRG1-433 only
Max. Load: 300W for Resistive Load
TM
enabled network. Every main
TM
logo can also be used with it
Package Content:
1pc 2GIG-Z-BRG1-433
(CT Clamp Bridge)
1pc
User Manual
)
° F
-1-
Z-Wave
Command Class:
™ ™ ™ ™
COMMAND_CLASS_SWITCH_MULTILEVEL
(Mapping COMMAND_CLASS_BASIC)
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_METER_V2
COMMAND_CLASS_PROTECTION
COMMAND_CLASS_VERSION
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Operation
TM
signal
If you are installing the entire Z-Wave
installation guide of Z-Wave
1.
Learning CT Clamp: Press program button before power on and green LED will flash
3 times, release the button till the green LED stay on. Switch on the CT Clamp. LED
shall go off after learning.
2.
For "Inclusion" in (adding to) a network: Put the Z-Wave
"inclusion" mode, and following its instruction to add the 2GIG-Z-BRG1-433 into your
controller. To get in the "Inclusion" mode, the distance between 2GIG-Z-BRG1-433
and controller is suggested to be in one meter. User can press program switch
once to be included.
For "Exclusion" from (removing from) a network: Set up the Z-Wave
Controller into "exclusion" mode, and following its instruction to delete the
2GIG-Z-BRG1-433 from your controller. Press program button to be excluded.
3.
2GIG-Z-BRG1-433 will store the latest energy usage (W & kWh) from CT Clamp,
and send to controller if the controller is asking for information.
4.
Manually turn the connected lighting On/Off by your controller or pressing the
program button. This is toggle switch. If the light is Off, pressing the button turns
the light On and vice versa.
connected lighting by your controller or pressing and holding the program button.
Release the button when the desired level is attained. This is toggle function. The
lighting will dim until the minimum level is attained or the button is released. The
next time the button is pressed and held, the level will increase until the maximum
level is attained or the button is released.
5.
Protection Function: User can use the Protection command class to disable the
Program Switch.
(1) Protection State=0x00 (Unprotected, Program Switch acts as normal);
(2) Protection State=0x01 (Protection by sequence, user can manual turn the
appliance on/off by press Program Switch 3 times, instead of 1 time);
(3) Protection State=0x02 (No operation possible, temporarily turn the Program
Switch function off).
TM
system for the first time, please refer to the
TM
Interface Controller before installing 2GIG-Z-BRG1-433.
TM
User can also adjust the brightness level of the
-2-
Interface Controller into
TM
Interface
Advertisement
