Platin Pro TXD Matrix TABLE OF CONTENTS Inside the Box ................................. 4 Product Map ................................... 4 Source Guide .................................. 5 Keypad codes and display ............................6 CH4 vs. CH8 modes ............................... 6 First time set up ................................7 Speaker Setup ................................8 PPA Series Speakers ..............................
Platin Pro TXD Matrix SOURCE GUIDE Source guide explains each source input and defines devices used *MIC/MIXER 2 input is layered over all zones regardless of source. MIC/MIXER 2 is added at 50% volume of zone...
Platin Pro TXD Matrix KEYPAD CODES AND DISPLAY Product map CH4 VS. CH8 MODES 4 Channel mode or CH4 is to be used when 4 independent zones are required or 4 different sources broadcast in 4 different areas. It can also be used to control volume of the same source in 4 zones.
FIRST TIME SET UP *Note - Platin Pro TXD Matrix works only with Platin Pro PPA, WS series speakers and ARX series receivers. Before powering on your TXD you must prepare your speakers and zones. It is advised to set up speakers at table height before mounting in high or difficult to reach spaces.
5. Left/Mono/Right - select which audio channel you need for this speaker 6. Set channel and speaker number - used for Platin Pro TXD and Platin Pro Wi-Fi Bridge, see transmitter user manual for instructions. Adjust speaker gain - use to adjust individual speaker if you need to balance several speakers in a room (0-99).
Platin Pro TXD Matrix PPA SERIES SPEAKERS 1. Find the Associate button, press and hold until you hear a tone. This erases any previous memory that may be in the speaker. 2. The LED display should read “00”, Wireless/Wired switch set to wireless and set L/M/R to M unless you need to define stereo channels L=left, M=mono (combined left and right) or R=right.
Platin Pro TXD Matrix WS SERIES SPEAKERS 1. Find the Associate button, press and hold until you hear a tone. This erases any previous memory that may be in the speaker. 2. For G1 WS 30 speakers they are preset to Mono and assigned to CH1, if you need Left or Right speakers or if you need to set them to a different zone contact your dealer for other preconfigured options.
Platin Pro TXD Matrix TXD SOURCE SET UP *Note - power off the TXD before connecting any new sources Referring to the Product Map, Source Guide and Keypad codes and display section above connect your additional sources. ZONE CONTROL This outlines how to control zones and zone volume; this section is for switching and volume control from the keypad and display on the TXD.
Platin Pro TXD Matrix EXAMPLES: 0107 = 0105 = 01+/- = 7000 = 8000 = USEFUL COMMANDS EXPLAINED Power cycle & release speakers – This function will communicate with all speakers connected and release them to be paired to another device or repair to the TXD.
Platin Pro TXD Matrix DISPLAY INFO & SETTINGS Bass adjust (all zone) – use volume buttons to adjust value up or down. Range -10 to 10 Treble adjust (all zone) – use volume buttons to adjust value up or down. Range - 10 to 10 Firmware –...
Platin Pro TXD Matrix WINDOWS INTERFACE SET UP DOWNLOADING WINDOWS SOFTWARE Visit www.platinpro.com/TXD to download PC software. Do not install until cable is attached to TXD CONNECTING THE USB TO RS232 CABLE TO PC AND TXD Included in the box, attach the USB end to a free USB slot on your PC, attach the RS232 to the TXD.
Platin Pro TXD Matrix TROUBLESHOOTING GUIDE Problem Solution Speaker not connecting Reset the speaker, hold down associate but until you hear the tone, add speakers on the TXD (9000+Input) Speaker not connecting Antennas in the speaker are on the right side as...
Platin Pro TXD Matrix IMPORTANT SAFETY INFORMATION • Read and follow all instructions, warnings and cautions when connecting the Platin audio hub and speakers. Keep these instructions for future reference. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Page 22
Platin Pro TXD Matrix cet appareil ne doit pas provoquer d’interférences néfastes, et cet appareil doit tolérer les interférences reçues, y compris celles qui risquent de provoquer un fonctionnement indésirable. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 23
Platin Pro TXD Matrix (i)Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. (ii) le gain d'antenne maximal autorisé pour les appareils dans les bandes 5250- 5350 MHz et 5470-5725 MHz doivent respecter le pire limiter;...
Our warranty to you: Platin Gate Technology warrants this product to be free of physical defects in material and workmanship for a period of 1 year from the date of the original purchase. If you discover a defect covered in this warranty we will repair or replace the product at our option.
Page 25
Platin Pro TXD Matrix H H H H ow to obtain service under this warranty: ow to obtain service under this warranty: ow to obtain service under this warranty: ow to obtain service under this warranty: By contacting your dealer for service and support, if they deem it necessary to return the product they will obtain an RMA ✔...
Need help?
Do you have a question about the Platin Pro TXD and is the answer not in the manual?
Questions and answers