Kensington CHO2802 Assembly Instructions

ASSEMBLY INSTRUCTIONS
WET
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALL
Kensington Medium Wall Lantern
1. Remove lantern cap (J) from lantern base (C) by unscrewing scre
Item # CHO2802
2. Insert glass panels (K) to each frame on lantern box (C).
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
3. Attach lantern cap (J) to top of lantern box, aligning the holes on b
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
Inserting screws (I) to secure lantern cap to lantern base.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
4. Attach ground (green) wire to ground wire from wall outlet box (us
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
a plastic wire connector. Tightly wrap the wire connector with elec
1. Remove lantern cap (J) from lantern base (C) by unscrewing screws (I).
IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PR
2. Insert glass panels (K) to each frame on lantern box (C).
3. Attach lantern cap (J) to top of lantern box, aligning the holes on bottom of
5. Connect neutral (white) fixture wire coming from fixture base to n
lantern cap (J) and top of lantern box (C). Inserting screws (I) to secure lantern
together with a plastic wire connector and tightly wrap the wire co
cap to lantern base.
4. Attach ground (green) wire to ground wire from wall outlet box (usually green
6. Repeat the procedure with the hot (black) wires. Always make sur
or copper in color), fasten together with a plastic wire connector. Tightly wrap
the wire connector with electrical tape so the end of the connector is sealed. IT
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS
IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY
7. Remove mounting plate (A) from lantern base (C) by removing ca
GROUNDED.
5. Connect neutral (white) fixture wire coming from fixture base to neutral (usually
8. Position the mounting plate (A) diagonally so that the holes of mo
white) outlet wire. Fasten both wires together with a plastic wire connector and
Tighten the mounting plate onto the wall outlet by mounting screw
tightly wrap the wire connector with electrical tape.
6. Repeat the procedure with the hot (black) wires. Always make sure that no wire
9. Gently push the lantern base (C) onto affixed mounting plate (A),
strands are left outside the connectors. DO NOT REVERSE THE HOT AND
on the lantern base (C) and tighten by screwing cap nuts (D) to th
NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
7. Remove mounting plate (A) from lantern base (C) by removing cap nuts (D).
10. Attach light reflector (H) to hook (E). Insert light bulb into socket.
8. Position the mounting plate (A) diagonally so that the holes of mounting plate
locking pin (F).
(A) and the wall outlet are aligned. Tighten the mounting plate onto the wall
outlet by mounting screws (B) provided.
11. INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND
9. Gently push the lantern base (C) onto affixed mounting plate (A), letting rods on
A. Mounting surface should be clean, dry, flat and 114" larger than
mounting plate pass through the holes on the lantern base (C) and tighten by
screwing cap nuts (D) to the exposed part of rods in clockwise direction.
the mounting surface and canopy exceeding 3/16" should be cor
B. With silicone (ex. GE-108) caulking compound, caulk complete
surface to prevent water from seeping into outlet box.