Table of Contents
Advertisement
Quick Links
P
ACIFIC
Recumbent Height-Adjustable
Bath System 9700 & Still Bath
Installation / Assembly Instructions
PENNER MANUFACTURING, INC
Box 523 / 102 Grant St.
Aurora, NE 68818
1-866-PENNERS
1-866-736-6377
1-800-732-0717
390745 Revision C 03/01/2008
E-mail Address: pennersales@hamilton.net
Pacific Recumbent Height
1
Adjustable Bath
Advertisement
Table of Contents
Related Manuals for Penner Pacific
Summary of Contents for Penner Pacific
- Page 1 ACIFIC Recumbent Height-Adjustable Bath System 9700 & Still Bath Installation / Assembly Instructions PENNER MANUFACTURING, INC Box 523 / 102 Grant St. Aurora, NE 68818 1-866-PENNERS 1-866-736-6377 1-800-732-0717 390745 Revision C 03/01/2008 E-mail Address: pennersales@hamilton.net Pacific Recumbent Height Adjustable Bath...
-
Page 2: Table Of Contents
Room Size Requirements Hot & Cold Water Supply Requirements Rough-In Requirements Pacific Bath Aqua-Aire Controls & Descriptions Pacific Bath Still Bath Controls & Descriptions Unpacking and Assembling the Pacific Bath Electrical Requirements Electrical Connection of the Pacific Bath Finishing up... -
Page 3: Introduction
These instructions are for the installation of a Pacific Recumbent Height Adjustable Bathing System 7900 Bath Panel and Bath Shell or Tank. This system is shipped on two pallets. The Pacific Bath Shell or Tank attaches easily to the Pacific Bath Panel. This system is a height adjustable tub. -
Page 4: Room Size Requirements
For optimum performance, dynamic pressures should be nominally equal. Maximum static supply pressure: 145 PSI. Maximum dynamic/maintained supply pressure: 81 PSI. Maximum supply hot water temperature: Consult local requirements for maximum allowed supply temperatures. (Not recommended over 110 Pacific Recumbent Height Adjustable Bath... -
Page 5: Rough-In Requirements
Rough-In Requirements Figure 2 Recommended water supply rough-in’s (wall or floor) and drain rough-in’s (wall or floor) Pacific Recumbent Height Adjustable Bath... -
Page 6: Pacific Bath Aqua-Aire Controls & Descriptions
Pacific Bath Control Panels Temperature Control Knob (Fill/Shower) Fill/Shower Water-Temperature Readout Tub-Temperature Readout Tub Fill ON / AUTO OFF Button Tub Fill OFF Button Tub Height Up Button Tub Height Down Button Pump or Aqua-Aire ON/OFF Button Rinse Jets Button (On tubs with Aqua-Aire only, Push and Hold) -
Page 7: Pacific Bath Still Bath Controls & Descriptions
Pacific Still Bath Control Panels Temperature Control Knob (Fill/Shower) Fill/Shower Water-Temperature Readout Tub-Temperature Readout Tub Fill ON / AUTO OFF Button Tub Fill OFF Button Tub Height Up Button Tub Height Down Button Disinfect Hand Spray Button (On/Auto Off) Hand Shower On/Auto Off (The unit has an adjustable time automatic shut-off) -
Page 8: Unpacking And Assembling The Pacific Bath
The Panel is left on the pallet until located in the area of installation. This pallet is 36” wide and will only fit through a 36” door. Move the pallet, with the Pacific panel on it, to the installation area by using appropriate dollies to avoid damage to the floor. - Page 9 Figure 14 Assemble both legs, extending forward, onto the base of the Pacific panel using the 4 ea. ½-13 bolts included in the installation kit. You will need a ¾” socket for the bolts. (See figure 13 & 14 above)
- Page 10 Unpacking and Assembling the Pacific Bath With the Pacific Panel still on the pallet, and the legs installed, two people can easily slide the whole panel forward on the pallet pulling on the legs until the front of the panel base is flush with the front edge of the pallet.
- Page 11 Figure 17 below. Do not use this cord for permanent connection. Figure 17 Now press the “UP” button of the Pacific Panel to slightly raise the panel about three inches or just above the lowering fixture. Figure 15 Insert the wooden lowering fixture, included in the Pacific Panel box, under the tub shell attachment brackets on the panel.
- Page 12 Unpacking and Assembling the Pacific Bath Figure 18 Figure 19 Note: It would be helpful to lower the Pacific Panel legs onto a piece of carpet or something similar to make it easier to reposition the panel to permanent location.
- Page 13 The lowering fixture should now be free to remove and discard once the legs are completely on the floor. Figure 20 You may now proceed to connect the tub shell to the Pacific Panel as follows: Open installation kit included in the box of the Pacific Tub shell.
- Page 14 Re-install the tub skirt onto the tub shell with the screws saved. WARNING Do not lift or maneuver the Pacific Bath Panel by lifting on the front and back Panels. Failure to avoid lifting on the fiberglass panels could cause damage to the unit and void your warranty.
-
Page 15: Electrical Requirements
• For the Aqua-Aire option (rated at 12 amps at 120 Volts) a 15 amp GFCI breaker will work. • See Figure 21 for location of field wiring connection point. Figure 21 • Pacific Recumbent Height Adjustable Bath... - Page 16 This unit is to be connected only by a licensed electrician. Electrical Requirements • The Aqua-Aire option of the Pacific Bath is rated at 12 amps at 120 volts. Therefore, a minimum of 15 amp GFCI circuit is required. Find the facility’s electrical junction box appropriate for powering the Pacific Bath.
-
Page 17: Finishing Up
If needed, Your PMI Products Representative will assist you with questions you may have in the operation of this equipment. For your nearest distributor, contact: PENNER PATIENT CARE, INC Box 523 / 102 Grant St. Aurora, NE 68818...