Subscribe to Our Youtube Channel
Related Manuals for Clemas & Co I-GUM
Summary of Contents for Clemas & Co I-GUM
- Page 1 I-GUM BATTERY POWERED OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.uk...
-
Page 2: Table Of Contents
CONTENTS Important Safety Instructions 01~03 Package Check List Machine Parts Preparation For Use 06~09 Installation 1 06~07 Installation 2 Instruction for control panel 10~11 Using the machine Turning OFF the machine Maintenance Trouble shooting Accessory Product Specification Electrical Diagram Exploded drawing and spare parts list 16~23 Safety Data Sheet 24~26... -
Page 3: Important Safety Instructions
Do not crush, pierce need to keep a distance to or damage in any way. READ ALL INSTRUCTIONS the integrated magnets in i-gum Do not heat or incinerate. BEFORE USING THE for 6 inch/15 cm when they are Do not short-circuit. -
Page 4: Installation
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE DO NOT OPERATE THE MACHINE WITHOUT READING AND UNDERSTANDING THE OPERATING INSTRUCTIONS. IF THE MACHINE IS OPERATED INCORRECTLY IT CAN POSE DANGER TO THE OPERATOR AND OTHERS AND WILL INVALIDATE THE MANUFACTURERS WARRANTY. - Page 5 IMPORTANT NOTICE: Always complete a test patch on the above surfaces to make sure no damage occurs to the flooring of surface Service Pack: When a machine is purchased, it require a service pack. Each service pack provides a continuous 8 hours operation and consists of: 4x Chemical Bottles Nylon wire Brush 3x Steel wire Brush...
-
Page 6: Package Check List
Package Check list: When you open the color box and you can find the parts as below showing: Machine: MAIN BODY 1x LANCE 1x Accessory: (Option2) (Option1) Top Battery 1x Broom with telescopic handle 1x Top Battery 1x Bottom Battery 1x Battery Charger 1x Power Cable Nylon Wire Brush 1x... -
Page 7: Machine Parts
Machine parts: Hose Control panel Broom Lance Trolley handle Shoulder harness & Waistband Fluid inlet hole Wheels Water drop disk Drawer Handle Brushes Storage Tube Battery Drawer Battery Power Display Power Switch Timer... -
Page 8: Preparation For Use
Preparation For Use Installation1. 1. Install the water drop disk to body. 2. Screw a steel wire or nylon wire brush onto the end of the nozzle of the lance. open close 3. Place the lance in the lance holder of body. There are 2 magnets which hold the lance in position. (The lance needs to be removed before the machine is fitted to the operative.) - Page 9 4. Open the brush storage tube cap and you can place the brushes in the tube. Insert the brush storage tube to the holder of body. 5. Assembly the brush to telescopic wand for the BROOM. 6. Insert the broom to broom holder of body. (The Broom needs to be removed before the machine is fitted to the operative.)
-
Page 10: Installation 2
Preparation For Use Installation 2 Before operating the machine: 1. Ensure that the battery has been fully charged before each operation. Before you charge the battery, please read the INSTRUCTION MANUAL OF BATTERY CHARGER first. The manual is in the package of the charger box. please keep the manual. 2. -
Page 11: Instruction For Control Panel
Preparation For Use INSTRUCTION FOR CONTROL PANEL ON/OFF Button: Power supply for handle control. RINSE Button,InFIRSTuse, press the RINSE button for about 1 minute to pour fluid into boiler to avoid boiler heating up without fluid. In NORMAL use, we do not need to press this button for 1 minute, because the fluid will flow to boiler from pipe after few seconds. -
Page 12: Using The Machine
Using the machine: LOGIC FOR FIRST TIME OPERATION ( Just for the first using ) Turn on the Mainswitch on body Turn on ON/OFF button on lance control panel Press RINSE button on lance control panel RISEN INDICATOR LIGHT flush, and pump will run in full speed. After about 1 minute, the fluid come out from brush of lance Release RINSE button on lance control panel Fluid in boiler will start to heat up and the heating indicator will flash,... -
Page 13: Turning Off The Machine
Using the machine: (DO NOT press Rinse button to wait for 1 minute) LOGIC FOR NORMAL USE Turn on the Main switch on body Turn on ON/OFF button on lance control panel Fluid in boiler will start to heat and heating indicator light will flush. Andpumpwillautomaticswitch-overtolowspeed After about 20 seconds, the fluid will be heated to steam and steam will come out from brush of lance... -
Page 14: Maintenance
Maintenance Machine maintenance The BATTERY VERSION I-GUM machine requires very little maintenance. Wipe down the machine periodically with a clean cloth. And wipe down the lance, and change the new brush for the lance. DO NOT spray water directly over the top of machine or top connector cap. -
Page 15: Trouble Shooting
Trouble shooting SOLUTION PROBLEM CAUSE No power to machine Insert to battery drawer No battery insert to battery drawer Power switch failure Replace power switch Replace cable or wire for hose cable or wire in hose broken The tank does not have any chemical in Input the chemical from bottles No steam come out The battery does not have energy charge the battery... -
Page 16: Product Specification
PRODUCT SPECIFICATION battery version i-gum Product Size (body unit): 347*330*500 mm Lance Size: 60*1100 mm Weight (Included 1x battery): 10.5 kg Lance Weight: 1.6 kg Broom Extended Length: 1.3 M Li-ion Battery: DC24V (25.2V,14Ah, 353 Wh”) Tank Capacity: 2.5 L... -
Page 18: Exploded Drawing And Spare Parts List
1/8 Exploded drawing and spare part list I-GUM LANCE EXPLODED DRAWING... - Page 19 LANCE page 2/8 spare parts list Item Part No. Discription Material Q'ty 106.0002.8 Control Panle PCB Battery Version 97.2004.31_remark Handle cover right, Gray 431C, PA66+20%GF 97.2003.31_remark Handle cover left, Gray 431C PA66+20%GF 106.0002.2 Handle Wand 106.1151.0 Soft Rubber For Lance Handle Rubber 106.1111.5 M4*6 Hex-sokect Botton Head Screw...
- Page 20 page 3/8 BODY UNIT EXPLODED DRAWING1...
- Page 21 page 4/8 BODY UNIT EXPLODED DRAWING2...
- Page 22 Bottom Housing parts assm (see exploded drawing) ABS, UL94-V0 S.106.2025.0 ASSY WATER TANK(see exploded drawing) 106.2001.1 I-GUM Body battery version 106.0139.1 logo sticker with printing "I-GUM" 106.2165.0 Water drop disk 106.2183.0 Hank screw for water drop disk SUS 304 106.1111.1...
- Page 23 page 6/8 Body spare parts list ... Connect with last page ... ITEM PART NO. DISCRIPTION MATERIAL Q'TY 106.1111.16 M4*10 Hex-sokect botton screw SUS 304 106.1111.15 M4*28 Hex-sokect botton screw SUS 304 106.2153.0 Bottom rubber foot plate Rubber 106.2157.0 Bottom cover ABS, UL94-V0 72.0261.0 Nut M4 nylon stainless steel...
- Page 24 page 7/8 Battery drawer spare parts list ITEM PART NO. DISCRIPTION MATERIAL Q'TY 72.0068.797 Battery Connector male, Blue 72.0057.0 Screw wn 5451 2.5*10 Ejot del TA PT SUS 304 106.2167.0 Battery Fitting Housing PC/ABS, UL94-V0 106.1111.1 M4*12 Flat hex-sokect botton scew SUS 304 106.2184.0 Al support rod for battery drawer...
- Page 25 page 8/8 ITEM PART NO DISCRIPTION MATERIAL Q'TY 97.0043.0 Breathing valve Rubber 106.2145.0 Rubber for fluid outlet cap Rubber 106.2166.0 Fluid level sensor pin 106.2185.0 LED light PCB for fluid tank LED, PCB board 106.2079.8 Wire for tank LED light PVC, Cu 106.2079.5 Wire for water detecting connector PVC, Cu...
-
Page 26: Safety Data Sheet
SAFETY DATA SHEET according to 1907/2006/EC, Article 31 Page GUM REMOVER SOLUTION Revision Revision date 2014-07-24 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Product name GUM REMOVER SOLUTION 1.3. Details of the supplier of the safety data sheet Company Merlin Chemicals Ltd Address... - Page 27 Page GUM REMOVER SOLUTION Revision Revision date 2014-07-24 5.2. Special hazards arising from the substance or mixture Wear suitable respiratory equipment when necessary. 5.3. Advice for firefighters Wear:. Self-contained breathing apparatus. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Ensure adequate ventilation of the working area.
- Page 28 Page GUM REMOVER SOLUTION Revision Revision date 2014-07-24 12.1. Toxicity No data is available on this product. SECTION 13: Disposal considerations General information Dispose of in compliance with all local and national regulations. SECTION 14: Transport information ADR/RID The product is not classified as dangerous for carriage. Not classified as hazardous for transport.
Need help?
Do you have a question about the I-GUM and is the answer not in the manual?
Questions and answers