Advertisement
Quick Links
Advertisement
Related Manuals for Motorline COFRE 600
Summary of Contents for Motorline COFRE 600
- Page 1 COFRE 600 INSTALLER AND USER’S MANUAL v1.1 REV. 12/2014...
-
Page 2: Safety Instructions
CONTENT SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW . CONTENT ATTENTION: índex | page To ensure the safety of people, it is important that you read all the following . SAFETY INSTRUCTIONS instructions.Incorrect installation or incorrect use of the product can cause physical standards to follow | page injury and material damage. - Page 3 TECHNICAL CHARACTERISTICS EXPLODED VIEW Awning COFRE 600 is an awning of large size, fully enclosed. It has articulated arms double cable, more robust and strong to give added strength and enable greater projection of the fabric. Optionally, the awning may be provided with an independent lighting kit that can be applied to the area protected by the awning.
- Page 4 INSTALLATION INSTALLATION INFORMATION PRE-INSTALLATION WALL WITHOUT CHOCKS NECESSARY FOR INSTALLATION AWNING Chock WALL WITH CHOCKS NECESSARY FOR INSTALLATION For correct operation of the awning, is obligatory placing the brackets (nº7) identicadas zones in the illustration (B). Always put one support on each side of the arm (image 2) AWNING and divide the rest in a balanced way.
- Page 5 INSTALLATION INSTALLATION CEILING 100mm 300mm 05 - Make the application of safe holders (nº7) in the wall bracket (nº6). 02 - Take the measurement the location where the awning will be applied always on the attention the leveling of wall brackets (nº6) for fixing the awning. 06 - Place the screws ISO 7380 (M10 x 30) with washers to fix the brackets nº6 to nº7.
- Page 6 INSTALLATION INSTALLATION INSTALLATION ON CEILING OPTION 1 OPTION 2 Make fixation on consoles (nº25) using one of the two options identified in the images 08 - Remove the screw and 09 - Open the awning with the crank (nº21) in 500mm 20 and 21 (use M12 screws with washers).
- Page 7 INSTALLATION INSTALLATION ADJUSTMENT THE ARTICULATION REGULATION OF INCLINATION OF ARMS Area to assistance in tuning the joint. Area to assistance in the regulation of inclination arms. RELIEVE 1 ARM EACH TIME 01 - To start the regulation of the inclination arms, place the awning in full open. Is to help the arms by hand in the whole process (J).
- Page 8 INSTALLATION INSTALLATION REGULATION THE TOP ADJUSTMENT THE MOTOR LIMIT SWITCH To optimize the awning closure is necessary to adjust the inclination of top (nº17), as a function of arm inclination (nº15). Put the open awning in about 500mm: tighten or loosen the screws (F, G), shown in the image 29, until the desired tuning is found.
- Page 9 INSTALLATION CONTROL BOARD REGULATION OF THE FABRIC TECHNICAL SPECIFICATIONS If you detect any abnormalities in the fabric winding (closing in an entire side only), make the opening of the awning and place plastic chocks in place identified in the image 36 (the side that does not close).
- Page 10 CONTROL BOARD CONTROL BOARD CONNECTIONS OF PLATE FUNCTIONS current absorption by a one parte of motor due to the possible presence of an obstacle Input connection Earth. or full movement opening / closing, the control board to immediately stop this Input connection Earth.
- Page 11 CONTROL BOARD CONTROL BOARD FUNCTIONS FUNCTIONS Programming sensor wireless sun / wind / rain TEST RAIN SENSOR Pass a wet finger over the sensor until the awning begins to close the awning will close during seconds . TEST WIND SENSOR Turn the propeller. The awning will close for seconds. TEST SUN SENSOR Turn VR clockwise + and the awning will open for seconds.
- Page 12 CONTROL BOARD CONTROL BOARD PROGRAMMING PROGRAMMING Menu Extensive CODE LAMP (Programming the remote control for operating the light inside of the awning) The control board is supplied by the manufacturer with the possibility of selecting only the The programming the channels of the remote control is performed as follows: position main menu functions.
-
Page 13: Troubleshooting
CONTROL BOARD TROUBLESHOOTING INSTRUCTIONS FOR CONSUMERS AND SPECIALIZED TECHNICAL Cancellation Codes The cancellation of all codes memorized for the functioning of awning remote controls and Wireless Sensor , proceed as follows: press the SEL button, LED CODE will flash, and then Problems Causes Solutions... - Page 14 CONNECTIONS TO CONTROL BOARD SCHEME OF CONNECTIONS (CONTROL BOARD MC6) CODE CODE L. FUSE FUSE 230V T.MOT. LAMP Ground wire Brown wire Blue wire Blue wire Brown wire Ground wire Alimentation (3x1.5mm²) Ground wire Circuit breaker 16A. not supplied Transformer LEDs Blue wire Brown wire...
- Page 15 CONTROL BOARD CONTROL BOARD FUNCTIONS FUNCTIONS Programming sensor wireless sun / wind / rain TEST RAIN SENSOR Pass a wet finger over the sensor until the awning begins to close the awning will close during seconds . TEST WIND SENSOR Turn the propeller. The awning will close for seconds. TEST SUN SENSOR Turn VR clockwise + and the awning will open for seconds.
Need help?
Do you have a question about the COFRE 600 and is the answer not in the manual?
Questions and answers