ToolPRO POWER CUT 25K Instruction Manual
  1. Manuals
  2. Brands
  3. ToolPRO Manuals
  4. Welding System
  5. POWER CUT 25K
  6. Instruction manual

ToolPRO POWER CUT 25K Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POWER CUT 25K and is the answer not in the manual?

Questions and answers

Summary of Contents for ToolPRO POWER CUT 25K

  • Page 2: Warranty

    To claim under this warranty, take this product to the Front Service Desk of your nearest CAUTION: Do not allow persons to operate or assemble this POWER CUT 25K Supercheap Auto store. For store locations, visit www.supercheapauto.com.au (AUS) machine until they have read this manual and have developed a thorough understanding or www.supercheapauto.co.nz (NZ).
  • Page 3   UV and IR Arc Rays - Follow the instructions in this manual. - Keep Cutter in the off position when not in use. The cutting arc produces ultraviolet (UV) and infrared (IR) rays that can cause injury - Connect ground lead as close to the area being cut as possible to ensure a good ground.  ...

  • Page 4: Product Introduction

    • Prohibit touching the contact part of the torch after the cutter is on. • Store idle POWER CUT 25K. When POWER CUT 25K is not in use, store it in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before Attention re-use.

  • Page 5: Technical Specifications

    Safety Check Each item listed below must be carefully checked before operation: POWER CUT 25K is high speed cutting equipment with advanced technology which is using • Make sure that the cutting machine has reliable earth connection. high density plasma arc as source of the heat. The plasma arc would be acquired by the •...
  • Page 6   Weight Ground   Dimension (L*W*H) 432*173*331 Descending   Plasma Cutting   Applying Norm of Cutter Power Source & AC 1 Phase   POWER CUT 25K conforms with the AS 60974-1standard to perform. 1 Phases Arc Welding transformer -- Rectifier...

  • Page 7: Appearance And Connection

    X: Duty Cycle APPEARANCE AND CONNECTION I1: Rated Input Current I2: Rated Cutting Current P1: Rated Input Power U0: Rated Open Circuit Voltage U1: Rated Input Voltage U2: Rated Load Voltage ~50Hz: AC, Rated Frequency 50Hz ...V: Unit of Voltage ...A: Unit of Current ...KVA: Unit of Power ...%: Unit of Duty Cycle...
  • Page 8 • Power Supply Configure of one Cutter: the torch’s electrode and puzzle. • It will be better to start cutting at the edge of the work piece, unless you must do ITEMS POWER CUT 25K perforation operation on the work piece. Air switch (A) ≥30 •...

  • Page 9: Troubleshooting

    TROUBLE SHOOTING Can’t cut or no current Torch is broken Examine and repair output Breakdown and Solutions Commutate module is Replace broken Breakdown Analysis Solutions AC contacting equipment is Replace broken Indication Light is off The light is broken Replace after turning on the Cutting thickness mode Replace...
  • Page 10 The Techniques Breakdown and Analysis Cutting thickness is Input compressed air pres- Adjust air pressure not up to the rated sure is too low or too high Breakdown Analysis Solutions standard Input compressed air flow is Adjust air flow Slag drop out from Work piece is not cut The cutting current is too Adjust ‘Cutting thickness...

  • Page 11: Parts List

      PARTS LIST Cut is too wide, Cutting speed is too slow Accelerate cutting speed processing quality Torch’s electrode or nozzle is Replace electrode or noz- is poor burnt down Cutting speed is too high Adjust cutting thickness mode to “thin” mode Type of nozzle is not right Replace with a suitable nozzle...
  • Page 12 Description Description Circuit Chart Handle Switch harness for gun Enclose Plastic frame Gas valve connector Gas regulator 220V AC Bracket for valve Potentiometer knob Cable holder Indicator light Rocker switch Welding potentiometer Input power line Gas power connector Plastic frame Main transformer Fan harness Insulating plate for transformer...

  • Page 13: Complete Set Specification

    COMPLETE SET SPECIFICATION Complete Set Supply • POWER CUT 25K • Cutting Torch • Earth Cable with Clamp • Operator’s Manual • Air Hose Notice: a) No guarantee has been made yet to get the accessories repaired at any time because of its breakable attribute.

Table of Contents