Table of Contents
Advertisement
Quick Links
Programmable 9-stage Battery Charger,
While this charger will work with most batteries out of the box,
it is very important to program it correctly for the best results.
It is critical you program the charger correctly before use!
Please see Page-7 or our Youtube video.
This manual contains important safety and operating instructions for this battery charger.
This battery charger is much more than just a charger, but also a maintainer and battery conditioner.
Suitable for all lead-acid battery types: Conventional wet cell, Calcium Sealed Maintenance Free
(SMF), AGM & Gel as well as Lithium (LiFePO4) battery setting option.
Battery diagnostics and smart multi-stage charging control and management will maximize battery life.
Special ECO low power consumption mode, ideal for permanent battery maintenance.
Automatic unique pulse-wave charging to activate LiFePO4 battery if it is protected by BMS.
Designed according to AS/NZS, EMC, UL/CUL, CE & FCC compliance.
Maintainer & Conditioner
Input:
100~240Vac, 50/60Hz
Output:
12V nominal (13.5Vdc) 1.0Amp
Model #
BCS12V1A
VERY IMPORTANT!
Lead based batteries:
Lithium batteries:
User's Manual
Please keep it with or near the charger at all times
INTRODUCTION
1
Page:
Revison: 7
Advertisement
Table of Contents
Summary of Contents for FMR BCS12V1A
- Page 1 Input: 100~240Vac, 50/60Hz Output: 12V nominal (13.5Vdc) 1.0Amp Model # BCS12V1A VERY IMPORTANT! Lead based batteries: While this charger will work with most batteries out of the box, it is very important to program it correctly for the best results.
- Page 2 FEATURES: Thank you for purchasing our new switched mode battery charger, the latest and patented technology is used in this device. It provides the following features: True switched-mode power Plug-and-play memory settings High frequency and low power consumption ...
-
Page 3: Preparing To Charge
CAUTIONS: Refer to battery manufacturer’s specific recommended values for battery type and charging rate setting. Do not charge to an improper type of battery. EG: do not charge AGM battery with Calcium battery setting If longer output charging cord is required; make sure the diameter is adequate for the current in given cable length. -
Page 4: Safety Protection
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY: Position the output DC cords to reduce risk of damage by bonnet, door or moving engine part. Stay clear of fan blades, belts, pulleys, and any other parts that can cause injury to persons. - Page 5 5.0 CHARGING CURVE 6.0 CHARGING STAGE CONTROL There are 9- stages of charging process controlled by program: Battery Diagnosis: Yellow LED flashing Initially detect the battery connected or not. Detect the battery voltage is healthy or not healthy. It will switch into Soft-start if battery is healthy. Detect if the battery is heavily discharged or not, it automatically run an additional enhanced “Recondition”...
-
Page 6: Specifications
SPECIFICATIONS Electrical Parameters Suit for battery type Lead acid and LiFePO4 Suit for battery capacity 2~30AH Rated charging current BCS12V/1A & BCS12V/1.5A 1.0 /1.5 Max. AC input voltage 100~240 AC input power frequency 50/60 Soft start charging current 0.1/ 0.15 Soft start battery voltage is over (for Lead acid battery) +/-0.2 Soft start battery voltage is over (for LiFePO4 battery) -
Page 7: Programming Table
PROGRAMMING NOTE! You can also visit our website for a Youtube video explaining this process. Step 1: Know your battery! The first step is to know your battery type. The default out-of-the-box setting will charge most lead- acid chemistry based batteries, but not optimally. To get the best results out of this charger you must program it to suit your battery type. - Page 8 Two year warranty The warranty covers this product to be free from defects in materials or workmanship for a period of two (2) years of the purchase date. Warranty does not cover modification, abuse, exposure to extreme environments outside of the design specifications (EG water or high temperatures), neglect, attempts to open/repair or lightning damage.