Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Samcon ExCam XPT Q6055
- Page 1 XPT Q6055 ExCam User Manual...
-
Page 2: Table Of Contents
Table of contents Introduction ......................4 Technical data ......................5 Explosion protection .................... 5 Electrical parameters of the camera ..............5 Connection cable Ex-d - Ex-e (ASKDP03-T) ............6 Video-technical characteristics ................7 Other technical data .................... 7 Safety Instructions ....................7 Assembly ........................ - Page 3 Table of Figures and Charts Fig. 2-1 Sectional view of ASKDP03-T ................6 Fig. 5-1 ExCam XPT Q6055 equipotential bonding ............11 Fig. 5-2 Camera (Ex-d) and terminal box (Ex-e) .............. 12 Fig. 5-3 Video Tutorial ExTB-3 ..................13 Tab. 5-4. Wire assignment of terminal box ExTB-3 ............13 Fig.
-
Page 4: Introduction
Introduction In the ExCam XPT Q6055 is a powerful IP dome camera of the latest generation, with 2- megapixel resolution at 1920x1080p points. It is certified by ATEX, IECEx and EAC-Ex. This dome camera can endlessly rotate around its own axis. When tilted, it covers a 180°... -
Page 5: Technical Data
Technical data Explosion protection Identification marks acc. to Directive 2014/34/EU: II 2G (zone 1 and 2) II 2D (zone 21 and 22) Explosion protection (gas): Ex d IIC T6 Gb Explosion protection (dust): Ex tb IIIC T80°C Db IP68 Protection class: IP 68 (IEC /EN 60529) 0°C…+40°C Transport/storage temperature:... -
Page 6: Connection Cable Ex-D - Ex-E (Askdp03-T)
Data line: 4 x 2 x AWG22/1 CAT.6a Performance elements: 3G1.5 (BK-BU-GN/YE) Properties: PUR halogen-free, flame-retardant, UV-resistant, chemical resistance, shielded (see www.samcon.eu Quick link: https://www.samcon.eu/fileadmin/documents/en/60-Assembling&mounting/ASKDP03-T_Datasheet.pdf Fig. 2-1 Sectional view of ASKDP03-T Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 6 of 28... -
Page 7: Video-Technical Characteristics
1 kg Dimensions D195mm x 378mm 145mm x 145mm x 71mm Safety Instructions Please absolutely adhere to the directions for safety in the installation instructions for the T08 ExCam series! Quick link: https://www.samcon.eu/fileadmin/documents/en/20-Ex-Cameras-Analog/ExCam-Series-T08-EX-Installation-Manual.pdf Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 7 of 28... -
Page 8: Assembly
Assembly Work preparation: Attention! Prepare your work carefully and in accordance with the relevant regulations. Attention! Depending on classification of hazard areas, a work approval has to be obtained. When you open the pressure-resistant enclosure under volt- age, it is absolutely necessary to prevent potentially explosive atmos- phere! To ensure the best image quality delivered by the network camera, plan the installation site carefully (consider light conditions, object distance or size, angle and minimum object... - Page 9 Drawings for drill hole patterns and further information can be viewed on our product page: Quick link: https://www.samcon.eu/en/produkte/netzwerk/excam-xpt-q6055/ Option mounting accessories WALL MOUNT EXCAM XPT (01538-001) Wall bracket Wall bracket for the T08-TNXCD series WMB-... Suitable for hanging the camera on walls.
-
Page 10: Electrical Connection
Electrical connection Attention! The electrical connection of the equipment must only be carried out by officially qualified and skilled personnel! Attention! ® It is absolutely necessary to ground the ExCam series housing via the PA connection. Attention! The minimum length of the connecting cable must not be less than three meters! The connection cable must be protected! Attention! Please pay attention to the national security, installation and accident... -
Page 11: Equipotential Bonding/Grounding
Equipotential bonding/Grounding Fig. 5-1 ExCam XPT Q6055 equipotential bonding Equipotential bonding/grounding of the camera body is absolutely necessary, in order to avoid static charges and formation of sparks. For this purpose, a screw terminal is pro- vided at the rear side, at the bottom (right) (see Figure 5.1). The cross-section of the... -
Page 12: Connection Work On The Device (Terminal Box)
Connection work on the device (terminal box) ExTB-3 Fig. 5-2 Camera (Ex-d) and terminal box (Ex-e) Attention! Connect the device the electric mains exclusively via the box ExTB-3 terminal! Attention! Never open the Ex-e terminal box under voltage! Attention! Adhere to the international installation regulations for connection chambers with increased safety (Ex-e). -
Page 13: Fig. 5-3 Video Tutorial Extb-3
Video Tutorial: Observe our video tutorial: “SAMCON 01 Installation and Wiring Connection to ExTB-3” https://www.youtube.com/watch?v=lqd5fsS7MsM Fig. 5-3 Video Tutorial ExTB-3 The pin assignment of the ASKDP03-T is executed in accordance with the standard EIA/TIA-568B for 100BaseTX and 24VDC, as follows:... -
Page 14: Fig. 5-5 Sample Circuit Of Terminal Box Extb-3
Fig. 5-5 Sample circuit of terminal box ExTB-3 Fig. 5-6 Photo of the occupied terminal box ExTB-3 Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 14 of 28... -
Page 15: External Connection And Protection
Bring the twisted pair composite approximately 10mm close to the ter- minals, in order to ensure the immunity to disturbance. Attention! Use only terminals approved by SAMCON. Attention! Finally, check your network installation by per Class-D Link Test. External connection and protection There are several options of assigning the ExTB-3 terminal box in a safe area: 5.3.1... -
Page 16: Routing Via Exconnection Rail (Optional Accessories)
Attention! Cables and wires must comply with the requirements of the IEC 60079-0/1/7 & 14. Attention! The supply line must have a sufficient cross-section. The cable pro- tection must comply with national and international regulations. 5.3.2 Routing via ExConnection Rail (optional accessories) Fig. -
Page 17: Appropriate Cables & Cable Entries
To see non-binding configuration and planning guidelines, please visit: https://www.samcon.eu/fileadmin/documents/en/99-Knowledgecenter/Cable-Gland-selection-for-Ex-d-enclosures.pdf In particular for installations which require a suitable barrier gland, make sure that you handle them correctly and adhere to the rules and notes given in the respective mounting instructions. -
Page 18: Fig. 5-9 Barrier Gland
Video Tutorial: Observe our video tutorial: “SAMCON 02 Installation Ex d gland” https://www.youtube.com/watch?v=U1nap29TEFY Fig. 5-9 Barrier gland Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 18 of 28... -
Page 19: Cable Kits - "Plug And Play" Connection Packages
5.3.4 Cable kits - "plug and play" connection packages As an option, there are various cable kits for different cables are available in different lengths. The connection packages include everything you need for a professional system installation: 10/25/95 m SKDP03-T system cable, digital (a) ... -
Page 20: Tab. 5-11 Available Cable Kits
Connection packages available: Length Non-armoured cable Armoured cable SKDP03-T ASKDP03-T SKDP03-T CABLE EXCAM 10M ASKDP03-T CABLE EXCAM 10M 10 meters (01540-001) (01543-001) This cable set includes: This cable set includes: 10 meters SKDP03-T system cable, digital 10 meters ASKDP03-T system cable, digital 1 x barrier gland Ex-d 1 x bolted connection Ex-d 5 ml Loctite 243 screw locking... -
Page 21: Fusing
Tab. 5-12 Recommendation for fusing 5.3.6 Plug assignment (RJ45) The data transfer of the ExCam XPT Q6055 series uses a 100 Mbit/s Ethernet connec- tion (100BASE-TX). If the cable termination uses a plug, (figure 5.3) it has to be plugged into the associated slot of the network device. -
Page 22: Tests Prior To Switching On Voltage
Attention! Finally, check your network installation by per Class-D Link Test. Observe our video tutorial: “SAMCON 03 Mounting and installing the RJ45 jack to SAMCON cables” https://www.youtube.com/watch?v=LOJ_7drrn4E&feature=youtu.be Fig. 5-13 Plug assignment RJ45 5.3.7 Tests prior to switching on voltage Attention! Prior to commissioning, all tests as indicated by the national regula- tions have to be executed. -
Page 23: Opening The Pressure-Resistant Housing
To open the TNXCD housing, you need a special tool. The customer should not open it. If you think that the housing has to be opened for unforeseeable reasons, please contact our support tem at first (Support@samcon.eu). Always adhere to the explosion-relevant rules: „WARNING –... -
Page 24: Network Access And Visualization
Interface, please see the User Manual for Axis or visit the following website: https://www.axis.com/products/axis-q6055 At delivery, the ExCam XPT Q6055 is set to the applicable net frequency (50Hz or 60Hz). If the camera is used at a location with a differing net frequency, a flickering of the picture might be noticeable, particularly in surroundings with fluorescent tubes. -
Page 25: Password/ Identification
It can also be used to manually assign a static IP address. For this purpose, the ExCam XPT Q6055 network camera has to be installed in the same physi- cal network segment (physical subnet) as the computer on which the AXIS IP Utility is running. -
Page 26: Maintenance/ Modification
Reparation Reparations must only be carried out with original parts of SAMCON Prozessleittechnik GmbH. Damaged pressure-resistant housings have to be replaced completely. In case of doubt, send the part in question back to SAMCON Prozessleittechnik GmbH. -
Page 27: Drawings & 3D Models
Drawings & 3D models All drawings, 3D models, certificates and other information are available in the download area of the product page on our website: https://www.samcon.eu/en/products/network/excam-xpt-q6055/ If you wish additional technical information, please contact us at: support@samcon.eu Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 27 of 28... - Page 28 Schillerstraße 17, 35102 Lohra-Altenvers, Germany www.samcon.eu, info@samcon.eu Phone: +49 6426 9231-0, fax: - 31 Doc.-ID: 180528-PT08BA-SS-ExCam XPT-Q6055_en_rev.00.docx, Page 28 of 28...