Supra DisplayKEY Installation Instructions

DisplayKEY Analog Modem Cradle

Installation Instructions

Introduction
The DisplayKEY cradle charges your DisplayKEY and
connects to the Supra system using an analog phone line to
update your DisplayKEY.
Connect Cradle
1. Insert one end of the provided phone cord into either of the
two phone ports on the back of the cradle.
2. Insert the other end of the phone cord into an open analog
phone line.
3. Insert the provided AC adapter into the AC connector and
plug the cradle into an electrical outlet.
If you do not have an open phone line, follow these steps to
share the line with your telephone:
1. Unplug your existing phone cord from the wall jack and
plug it into either of the phone ports on the back of the
cradle.
2. Plug the phone cord provided with your DisplayKEY cradle
into the remaining open port on the cradle and connect the
other end to the phone jack in the wall.
Figure 1 DisplayKEY analog modem cradle setup
Using your DisplayKEY Cradle
Once your cradle is set up, charge your DisplayKEY by placing
it in the cradle, matching the contacts on the top of the key with
the contacts on the cradle. Charge your DisplayKEY for at least
four hours before using it. After the initial charge, it only takes a
few minutes a day to recharge your DisplayKEY during regular
use.
Perform a manual eSYNC to verify that the installation was
successful. Turn on your DisplayKEY by pressing the Enter
button. Scroll to MANUAL ESYNC and press Enter, then place
your DisplayKEY in the cradle.
© 2011 UTC Fire & Security. All rights reserved.
The light on the front of the cradle indicates the cradle status.
Green indicates that the DisplayKEY is successfully connected
to the cradle and is charging, and amber indicates that the
DisplayKEY and cradle are communicating. When the cradle
light is red, a process called eSYNC is occurring. Do not
remove the DisplayKEY from the cradle when the light is red.
After an eSYNC, the DisplayKEY's status is displayed on the
screen. We recommend placing your DisplayKEY in the cradle
each night to ensure that it is updated and fully charged each
day.

FCC Compliance

Part 15 information. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference
to radio communications.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Part 68 information. This equipment complies with Part 68 of the FCC
Rules and the requirements adopted by ACTA. On the bottom of the en-
closure of this equipment, a label contains a product identifier in the format
US:AAAEQ##TXXXX. If requested, this information must be provided to your
telephone company.
The plug and jack used to connect this equipment to the premises wiring
and telephone network comply with the applicable FCC Part 68 rules and re-
quirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may connect to
a telephone line. Excessive RENs on a telephone line may result in the de-
vices not ringing in response to an incoming call. In most but not all cases,
the sum of the RENs should not exceed five (5.0). To be certain of the num-
ber of devices that may connect to a line, as determined by the total RENs,
contact your local telephone company. For product approved after July 23,
2001, the REN for this product is part of the identifier that has the format
US:AAAEQ##TXXXX. The digits represented by the ## are the REN without
the decimal point. (For example, 03 is a REN of 0.3.) For earlier products, the
REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone com-
pany will notify you in advance that temporary discontinuance of service may
be required. But if advance notice isn't practical, the telephone company will
notify you as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, op-
erations, or procedures that could affect the proper functioning of your equip-
ment. If it does, you will be notified in advance in order for you to make
necessary modifications to maintain uninterrupted service.
If your home has specially wired alarm equipment connected to the tele-
phone line, ensure the installation of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equip-
ment, consult your telephone company or a qualified installer.
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission, or corporation commis-
sion for information.
If you experience trouble with this equipment, or for warranty/repair informa-
tion, please contact the support number listed in this document. If the equip-
ment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved. DO
NOT DISASSEMBLE THIS EQUIPMENT.
P/N 10102958P1 • March 2011