Enterasys C5110 Quick Reference page 2

Installing in a Rack
A rack mounting kit and Rack Installation Instructions are included with
the controller. The rack mounting kit allows you to install the controller
into a four‐post rack cabinet. Refer to the installation guide for complete
installation instructions.
Rack Mounting Kit Details
Mounting Interface: ReadyRails™
Rail Type: Sliding
Rack Types Supported: 4‐Post Square Holes and 4‐Post Unthreaded
Round Holes
Rack Adjustability Range: (represents the allowable distance between the
outside‐facing surfaces of the front and rear mounting posts of the rack)
Square Holes:
Minimum: 692 mm (27.2 in)
Maximum: 756 mm (29.7 in)
Round Holes:
Minimum: 678 mm (26.7 in)
Maximum: 749 mm (29.5 in)
Rail Depth: (represents the minimum depth of the rail as measured from
the rack front mounting posts when the rail rear bracket is positioned all
the way forward)
Without Cable Management Assembly: 768* mm (30.2 in)
(* With outer CMA brackets removed)
With Cable Management Assembly: 887 mm (35 in)
Getting Help
For additional support related to your module, or this document, contact
Enterasys Networks using one of the following methods:
World Wide Web www.enterasys.com/support/
1-800-872-8440 (toll-free in U.S. and Canada)
or 1-978-684-1000
Phone For the Enterasys Networks Support toll-free number in
your country:
www.enterasys.com/services/support/contact/
support@enterasys.com
Internet mail
To expedite your message, type [Wireless] in the subject
field of your message.
The latest image and www.enterasys.com/services/support/downloads/software
release notes
Documentation URL: http://www.enterasys.com/support/manuals
Notice
Enterasys Networks reserves the right to make changes in specifications and other
information contained in this document and its web site without prior notice. The
reader should in all cases consult Enterasys Networks to determine whether any such
changes have been made.
The hardware, firmware, or software described in this document is subject to change
without notice.
IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY
INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING
OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION
CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED
OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH
DAMAGES.
Enterasys Networks, Inc.
50 Minuteman Road
Andover, MA 01810
© 2009 Enterasys Networks, Inc. All rights reserved.
Part Number: 9034514‐01 September 2009
ENTERASYS, ENTERASYS NETWORKS, ENTERASYS SECURE NETWORKS,
ENTERASYS MATRIX, and any logos associated therewith, are trademarks or
registered trademarks of Enterasys Networks, Inc., in the United States and/or other
countries. For a complete list of Enterasys trademarks, see
http://www.enterasys.com/company/trademarks.aspx.
All other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies.
Regulatory Compliance Information
For complete regulatory compliance and safety information, refer to the Product
Information Guide that was shipped with this product.
Federal Communications Commission (FCC) Notice
This product has been tested and found to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This product uses, generates, and can radiate radio
frequency energy and if not installed and used in accordance with the manufacturer's
instruction manual, may cause harmful interference to radio communications.
Operation of this product in a residential area is likely to cause harmful interference,
in which case you will be required to correct the interference at your own expense.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Notice: The FCC regulations provide that changes or modifications made to this
device which are not expressly approved by Dell™ Inc. could void your authority to
operate the equipment.
Dell Inc. is the responsible party for this product. For an EMC compliance issue or a
regulatory inquiry, please use the following contact information:
Dell Inc.
Worldwide Regulatory Compliance, Engineering and Environmental Affairs
One Dell Way PS4‐30
Round Rock, Texas 78682 USA
512‐338‐4400
Industry Canada, Class A
This Class A digital apparatus complies with Canadian ICES‐003.
Notice: The Industry Canada regulations provide that changes or modifications not
expressly approved by Dell Inc. could void your authority to operate this equipment.
Cet appareil numérique de la classe A est conforme à la norme NMB‐003 du Canada.
Avis: Dans le cadre des réglementations d'Industry Canada, vos droits d'utilisation
de cet équipement peuvent être annulés si des changements ou modifications non
expressément approuvés par Dell Inc. y sont apportés.
CE Notice
This product has been determined to be in compliance with 2006/95/EC (Low Voltage
Directive), 2004/108/EC (EMC Directive), and amendments of the European Union.
Versions of this product may have integrated modules or add‐in cards supporting
wireless and telecommunications operations. These wireless and telecommunications
peripherals have been assessed as compliant in this product and, when present, are in
compliance with 1999/5/EC (R&TTE Directive, for Radio and Telecommunications
Interfaces).
European Union, Class A
Warning: This is a Class A product. In a domestic environment this product may
cause radio frequency interference in which case the user may be required to take
adequate measures.
A "Declaration of Conformity" in accordance with the preceding directives and
standards has been made and is on file at Dell Inc. Products Europe BV, Limerick,
Ireland.
VCCI Notice
This is a class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is used
in a domestic environment, radio disturbance may arise. When such trouble occurs,
the user may be required to take corrective actions.
BSMI EMC Statement — Taiwan
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Supplement to Product Instructions
(Hazardous Substance)
(Parts)
(Metal Parts)
Circuit Modules)
Cables & Cable Assemblies)
(Plastic and Polymeric parts)
Circuit Breakers)
SJ/T 11363-2006
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T 11363-2006 standard.
SJ/T 11363-2006
Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard.
This table shows where these substances may be found in the supply chain of Enterasys' electronic
information products, as of the date of sale of the enclosed product. Note that some of the component types
listed above may or may not be a part of the enclosed product.
50
The Environmentally Friendly Use Period (EFUP) for all enclosed products and their parts
are per the symbol shown here, unless otherwise marked. Certain parts may have a
different EFUP (for example, battery modules) and so are marked to reflect such. The
Environmentally Friendly Use Period is valid only when the product is operated under the
conditions defined in the product manual.
Hazardous Substances
This product complies with the requirements of European Directive, 2002/95/EC,
Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment.
European Waste Electrical and Electronic Equipment (WEEE) Notice
In accordance with Directive 2002/96/EC of the European Parliament on waste
electrical and electronic equipment (WEEE):
1. The symbol above indicates that separate collection of electrical and electronic
equipment is required and that this product was placed on the European market
after August 13, 2005, the date of enforcement for Directive 2002/96/EC.
2. When this product has reached the end of its serviceable life, it cannot be disposed
of as unsorted municipal waste. It must be collected and treated separately.
3. It has been determined by the European Parliament that there are potential
negative effects on the environment and human health as a result of the presence
of hazardous substances in electrical and electronic equipment.
4. It is the users' responsibility to utilize the available collection system to ensure
WEEE is properly treated.
For information about the available collection system, please go to
www.enterasys.com/services/support/ or contact Enterasys Customer Support at
353 61 705586 (Ireland).
Declaration of Conformity
A "Declaration of Conformity" in accordance with the preceding directives and
standards has been made and is on file at Dell Inc. Products Europe BV, Limerick,
Ireland.
®
Enterasys Wireless
Controller C5110
Quick Reference
P/N 9034514-01