Advertisement
Quick Links
Read the technical instructions before installing the bath
Do not bring sharp objects into the bath
Contact the seller if the colours appear to be changing under or on top of the coating
If a leakage appears it should be resolved from inside and without any delay
All electrical work should be perfomed by a qualified electrician
The buyer is responsible for ensuring that the instructions are followed even if
assembly is performed by a third party.
ATTENTION! If the hot tub will be integrated e.g. into a terrace it is necessary that the
access is not obstructed in any way order to be able to service it. Service hatch and
outer panel should be removable without difficulties.
AquaKing
Additional Instructions
WARNING
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Polar Spas AquaKing
- Page 1 AquaKing Additional Instructions WARNING Read the technical instructions before installing the bath Do not bring sharp objects into the bath Contact the seller if the colours appear to be changing under or on top of the coating ...
- Page 2 2289 1782 Water drainage and electric wiring Hose Ø 33 mm Article Part Number Material Page Size AquaKing Polar LunaWood 2248 Designed by Scale JI 01.10.08 1:18 Checked by Revision v 2.1 Aproved by Sheet 22/22...
- Page 3 Additional assembly instructions for Polar AquaKing (v. 092009) Thank you for choosing a product from SpaDealers. Polar AquaKing is a unique wooden spabath with a plastic inner lining and edging. This makes cleaning easy and protects the wood. When assembling it is very important to follow the instructions in order to avoid leakages. Please read our guarantee conditions and what they include.
- Page 4 After the caulking has been completed, the bubble system’s hoses can be assembled. Note that the placement in picture 12 shows the AquaKing Jets, where one vertical part (at the very bottom) has a hole for connection to an extra pump for optional extra jets and lamp. The AquaKing Standard without extras doesn’t have these extra holes.
- Page 5 When everything else has been assembled, including the thermostat sensor and skimmer. Use silicone in the hole for the screws. If you have an AquaKing Jets, all the jet nozzles should also be mounted with included hose connections. Follow separate instructions. HINT! This can be also done while the joints are drying.
- Page 6 leakage above the benches. If not enough care has been taken when assembling the side modules, there is a risk that a crack could occur in the thin part of the inner tongue. In such cases, the risk of leakage above the joint between the benches and side module is high, and almost always there is then a leakage in the side stave tongue, which makes water drip in the lower end.
- Page 7 Mask properly In order to make the work on the joints easier and more secure (no leaks) it is important that the masking is done in accordance with our directions. We also recommend that the joints are coated afterwards to protect against chemicals and eventual wear on the joints.
- Page 8 The same principle is used for all parts that will be joined and coated. ~20mm ~20mm...
- Page 9 ~5mm ~10mm...
- Page 10 Mask the base parts according to the same principle Begin masking the side modules when the joints on "sitting well" are done.
- Page 11 Trim the masking tape for the coating about 1 cm in from the line that marks the joints. See guide “Sanding” before doing this step 1. Mask with tape along the lines for the joints on both sides. 2. Then do the lower line for the joint. 3.
- Page 12 Coating of joints Improper use of chlorine, or some other combination of chemicals, can damage the sealing mass that is used on the joints. It’s therefore recommended that the joints on the benches, between the side and bottom modules are treated with a layer of coating to protect them. The joints first have to be dry and clean. This guide describes this process in detail during the assembly stage.
- Page 13 SANDING To ensure the coating will take a firm hold, sanding shall be done inside the first masking and out against the edge before the second masking is applied.
- Page 14 Second Coating 2. Masking removed 1. First coating 3. Apply new masking at the outer edges, 3.1 Lightly sand inside the masking folliwing the same line as before, when it has dried. 4. Apply masking along the innermost 5. The sides are assembled and a joint is black line on the seating well.
- Page 15 Bubble system assembly Picture shows parts, Drive the air jet into the hole using a rubber mallet. Note! Remove gasket before. Hold it from underneath and support the part with your arm. Remove the air jet. Gasket Gasket Picture shows air jet + gasket installed. Assemble the air jet.
- Page 16 The airjet should be coated with silicon before the Apply silicon on the airjet T-connection is attached Silicon applied Smear out the silicon Attach the T-connection The finished part.
- Page 17 – Gäller endast om du har AquaKing Jets – – Only applies if you have AquaKing Jets –...
- Page 19 The pictures show the installation of the temperature sensor.
- Page 20 Assembly of edge Picture shows one section of the edge and placement of the parts. Apply masking tape as shown on picture Then apply sealing sikaflex in the joint Remove masking tape. Repeat procedure Spread out the mass as see in in picture 3 for remaining joints.
- Page 21 Mask with tape about 1cm below the hot tubs lower edge before the rim is attached. See steps 36-37 in the main assembly guide on how to assemble the rim. When the edge is in plane, mask the edges Apply a new layer of tape on top that goes on the edge with masking tape and sand the all the way to the edge.
- Page 22 Remove the top layer of masking tape Repeat the procedure for every joiint, when the mass has dried apply TubCoat over the quickly. joints and remove the remaining masking tape. Apply silicone around the hole before you insert the plastic plug. After the silicone has dried excess material can be pulled off.
- Page 23 It should not be oriented with the air exhaust upwards. If the AquaKing is equipped with the BactiSafe (accessory) then it is positioned according to picture 1. The control system is fastened in the position that is shown in picture 2.
Need help?
Do you have a question about the AquaKing and is the answer not in the manual?
Questions and answers