noisehush N600 Instruction Manual

N600 Instruction Manual
Please Read Before Operation
Product Description:
The "NoiseHush N600 Handsfree Kit" supports headset &
handsfree pro le phones. Providing advanced audio
quality, it features full DSP Noise & Echo Cancellation. It is
designed for easy, handsfree operation and outstanding
performance.
Don't forget: Drive safely and obey the law.
Please refer to relevant National or local legislation,
notably the limitations regarding the usage restraints of
mobile phones while driving.
Charging the Handsfree Speakerphone:
Please fully charge the battery before using. It will take
about 2.5 hours to charge completely.
The charging steps are as follows:
Step1: Connect charger or charging cable to a standard
vehicle charger socket or any computer USB.
Step2: Connect the end of the charging cable to the
charging port of the side of the unit.
When the Red LED is on, it is charging. When the Red LED
is o , it has charged completely.
Low power - When you hear 3 tones every 10 seconds or
see the Red LED ash twice every 10 seconds, it means
that the battery is low on power and needs to be
charged.
Pairing NoiseHush "N600" Bluetooth Handsfree
Speakerphone with your Cell Phone.
Pairing will create a stored connection in the handsfree
speakerphone and your Bluetooth cell phone. Pairing has
to be done only once, when rst connecting to a phone.
1. First turn the phone OFF and then back ON to refresh
its memory.
2. Bring the mobile phone to about 30cm from
NoiseHush N600 speakerphone.
3. Find the Bluetooth menu in your mobile phone. Turn
Bluetooth ON. (Check your phone's User Manual.)
4. Make sure the N600 speakerphone kit is OFF. Press
and hold the Function button for about 7-9
seconds, and release it when the Red and Blue LEDs
ash alternately.
5. Your headset is now ready to be discovered by your
Bluetooth mobile phone.
6. Perform a Bluetooth device discovery on your mobile
phone to add a new device. It takes a few seconds to
search for and nd other Bluetooth devices around
you.
7. When Bluetooth devices are found, the phone will
display "NoiseHush N600". Scroll to it and press OK to
con rm that you want to pair the devices.
8. Enter the Passkey "0000" when your phone prompts
you. The phone will now pair with the "N600".
9. If your Bluetooth phone menu supports it, "set as
authorized" or "add to trusted devices."
10. Again select the "NoiseHush N600" to con rm the
connection.
11. If the pairing is not successful, the "NoiseHush N600"
will return to the standby mode. Please repeat the
pairing process to try the pairing again.
12. Refer to your cell phone's User Manual for any
additional steps.
1 Function button
- On/O , Pairing,
Answer, Voice Dial,
Redial, Last Call and
Mute, Transfer a call
2 End and Cancel Call,
Reject calling
3 Volume Up
4 Volume Down
5 Speaker
6 Dual Microphone
7 Charging Port
8 Magnet
9 Metal Fixed Clip
Speakerphone Functions:
Not all mobile phones support the function listed below, please refer to your mobile
phone's user manual for more information regarding your phone's features.
Function Handsfree Status
Power On OFF
Power O Standby
Enter Pairing OFF
Mode
Cancel a call Calling
Answer a Call Ringing
Reject a Call Ringing
End a Call During a Call
Volume Up During a Call
Volume Down During a Call
Mute the During a Call
Microphone
Unmute the During a Call
Microphone (Microphone Mute)
Redial Last Standby (Connected
Call with Device)
Voice Dial Standby (Connected
with Device)
Transfer Call During a Call
between mobile
and Handsfree
Kit
Attaching the Handsfree Kit:
Install the metal clip on your visor. Attach the metal clip
of the N600 to the vehicle's sun visor. Align & attach the
magnets on the rear of the N600 to the metal clip.
For Optimum Handsfree Quality:
The NoiseHush N600 must be placed in a position
ensuring that the microphone is directly in the path of
the User's voice.
Important Notice: Automatic Switching O
This N600 Handsfree Speakerphone is programmed with
a special battery saving feature which will automatically
power o in 10 minutes when not connected to a paired
mobile phone.
LED (and Tone) Indicator Chart:
During Calling Blue LED is steadily ON
Standby Mode (Not Connected) Blue LED ashes 1 time every 2 seconds
Standby Mode (Connected) Blue LED ashes 1 times every 30 seconds
Pairing Mode Red and Blue LEDs ash alternately
Active Call (Ringing) Blue LED ashes quickly
Low Battery Red LED ashes twice every 10 seconds,
also will beep 3 tones every 10 seconds
Charging Red indicator is steadily ON
Charging Complete Red indicator turns OFF
Note: If the charger is plugged in while the N600 is in use, the unit will
automatically turn OFF. To turn the N600 back on, simply press and hold
Function button till the unit turns on. The LED will ash with one tone.
Contact Us:
For additional help or to purchase accessories such as
AC/DC, please visit us at www.noisehush.com.
Operation
Press Function button for 3∼5
seconds, Blue LED ashes, one tone.
Press button for 3∼5 seconds,
Red LED ashes, one tone.
With the handsfree kit is o ,
press button for about 7∼9
seconds, release when Red and Blue
LEDs ash alternately, two beeps.
Press End button 1 time.
Press Function button 1 time.
Press End button once.
Press End button 1 time.
Press + button.
Press - button.
Press Function button 2 times
(Tow tones every 5 seconds when
microphone is mute).
Press Function button 2 times.
Press Function button 2 times.
Press Function button 1 time.
To transfer the active call between
handsfree kit and mobile phone,
press the Function button about
2 seconds, and release till hearing
a tone.