PIQS TT Quick Start Manual

Proceed as follows to avoid any moisture build-up:
1. Seal this device in a plastic bag before moving it to another
Disclaimer room, in order for it to adapt to room conditions.
2. Wait one to two hours before you take the device out of the
The information in this document, photos and
plastic bag.
packages are subject to change without notice. The
m a n u f a c t u r e r m a k e s n o r e p r e s e n t a t i o n s o r
·The device should not be used in a very dusty or very bright
warranties with respect to the contents hereof and
(sunlight) environment. Dust particles and other foreign
specically disclaim any implied warranties of
objects may damage the unit. Bright light (Sunlight) may
merchantability or tness for any particular purpose.
interfere the remote controller sensor.
The manufacturer reserves the right to revise this
·Do not expose the device to extreme vibrations. It may damage
publication and to make changes from time to time in
the internal components.
t h e c o n t e n t h e r e o f w i t h o u t o b l i g a t i o n o f t h e
·The packing materials should be kept out of the hands of
manufacturer to notify any person of such revision or children.
changes.
Safety
Buttery Technology (Shenzhen) Limited.
Address: 6F Building 1, No. 35 Cui Jing Road, Pingshan New District,
Shenzhen, 518118, P.R.C.
Tel: 86-755-86139000
Fax: 86-755-86139206
Http: www.piqs.com
is a trademark of Buttery Technology (Shenzhen) Limited.
Other trademarks are the properties of their respective owners.
-9-
Power Supply
Use only the enclosed power adapter. Check whether the
mains voltage of the power supply matches the mains voltage
available at the setup location. This equipment complies with
the voltage type specified on the unit.
The capacity of the remote controller battery and the
projector diminishes with time, check the status light or
warning message. Do not overcharge the battery for more
than 24 hours.
Remote controller uses Laser in order to interact with the
Do not try to replace the battery yourself. Incorrect handling
image screen, therefore do not stare at the front of the remote
of the battery or using the wrong type of battery can cause
controller.
damage to the device or cause injury.
· Switch the device on or off using the power switch before
removing the power supply from the socket.
· Turn off the device and remove it from the power supply
before cleaning the surface.
· Use a soft and dry cloth. Never use liquid, gaseous or easily
f l a m m a b l e c l e a n s e r s ( s p r a y s , a b r a s i v e s , p o l i s h e s ,
alcohol). Do not allow any moisture to reach the interior of
the device.
Repairs
Do not make any repairs to the device yourself.
Improper maintenance can result in injuries or damage to the
device. Only have your device repaired by an authorized
service center.
Do not remove the type label from your device; this would void
the warranty.
-10- -11-
Limited Warranty NOTE:
We promote its products of highest quality and we make the This equipment has been tested and found to comply with the
following limited warranty to original consumers of its limits for a Class B digital device, pursuant to part 15 of the
projectors sold in our official resellers/dealers. FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
·This product and its accessories are warranted for One
installation.
year from the date of purchase.
This equipment generates, uses and can radiate radio
·This warranty only applies if the product has been used in
frequency energy and, if not installed and used in accordance
accordance with the manufacturers' instructions under
with the instructions, may cause harmful interference to radio
normal use and with reasonable care.
communications. However, there is no guarantee that
·This warranty does not cover:
interference will not occur in a particular installation. If this
*Damage to the Projector that is caused by accident, equipment does cause harmful interference to radio or
misuse, abuse, negligence, alteration (including rooting
television reception, which can be determined by turning the
the unit), natural disaster, or unauthorized repair of the equipment off and on, the user is encouraged to try to correct
projector;
the interference by one or more of the following measures:
*Improper or incorrectly performed installation, setup, - Reorient or relocate the receiving antenna.
operation, repair or maintenance;
- Increase the separation between the equipment and
·For detailed information of warranty, please contact your
receiver.
dealers or retailers directly.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Regulatory Information
- Consult the dealer or an experienced radio/TV technician
for help.
Model：TT
FCC ID:2ALH2-PFAT100
IC:22519-PFAT100
RF Exposure Statement:
WARNING:
For the product, under normal use condition is at least 20cm
away from the body of the user, the user must keep at least
This device complies with part 15 of the FCC Rules.
20cm distance to the product.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u n d e s i r e d
o p e r a t i o n , c h a n g e s o r m o d i f i c a t i o n s n o t e x p r e s s l y
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
-12- -13-
IC Caution
Attention IC
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1) this device may not cause interference,
2) and this device must accept any interference, including Virtual Touch Projector
interference that may cause undesired operation of the
device.
Model: TT
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage
r a d i o é l e c t r i q u e s u b i , m ê m e s i l e b r o u i l l a g e e s t
susceptible d'en
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Android is a trademark of Google Inc.
DLP is a trademark of Texas Instruments Inc.
All other product names used in this manual are the properties of their respective
owners and are acknowledged.
EN Quick Start Guide
-14-