Page 1
User Guide and Installation Manual RF DISTRIBUTION HUB FOR, BUT NOT LIMITED TO, P/N’S ZBT0100052 24 PORT HUB ZBT0100055 24 PORT HUB W/ FIBER RX ZBT0100051 16 PORT HUB ZBT0100054 16 PORT HUB W/ FIBER RX ZBT0100050 8 PORT HUB ZBT0100053 8 PORT HUB WITH FIBER RX REV 1.0...
Safety Precautions The presence of this symbol is to alert the installer and user to the presence of uninsulated dangerous voltages within the product’s enclosure that may be of sufficient magnitude to produce a risk of electric shock. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE.
MHz, thru CAT cable (5e or better) per EIA/TIA 568 standards to up to 24 end devices (Active baluns, Z-Band P/N ZBT00100085: Recommended for full feature set, P/N ZBT0010021: Reduced feature set) which go to a TV Tuner. The hub accepts either a 75Ω RF input, or an optional Fiber input. The system also provides an RF “cascade”...
DISTRIBUTION ZHC Specifications Physical Description Dimensions: 17” wide x 1.7/16” x 12” deep (designed for 1RU of rack space) Weight: 7lbs (total box weight including external power supply) Electrical Power Power Consumption 12VDC/8.5A 102W MAX External Power Supply Input Voltage 100-240V AC, 50-60Hz, 1.4A Max BTU/HR 358 BTU/HR (MAX)
Page 6
UL/CSA Listed Resolution Video Resolution : Z-Band system performs no manipulation of the video programming. All visible and non-visible content is passed through to the viewing/decoding equipment. This includes but is not limited to closed captioning, EAS data, alternate languages, and any resolutions within the video channel.
Installing a Distribution ZHC requires the following: 1. Standard Rack Mounting tools 2. Field RF Meter capable of measuring levels and signal quality. (Z-Band can assist with evaluating or procuring the proper equipment). A proper installation cannot be done without out the appropriate meter! Z-Band can be of minimal help in diagnosing issues without a meter on site.
“F” connectors to cable the coax cascade backbone to all units (Reference Following Cascade section). Recommended that you use Z-Band design drawing. 2. Connect the CAT patch cords from the front panel RJ45’s to the proper port in the Patch Panel.
Z-Band for assistance in reconfiguring the unit. All connections in the fiber links must be either fusion spliced or Angle Polished (APC). All connections on Z-Band furnished equipment has SC/APC.
Page 10
Fiber TX manufacturer’s guide for proper channel load/level set-up. At RF headend adjust signal so that the input to the Z-Band Light Fiber TX is 20+/-2 dBmV for all channels across the spectrum for digital, or is 23 dBmV+/-2 for analog. It is extremely important that the whole spectrum is FLAT (0 slope) for the system to preform properly.
DISTRIBUTION ZHC Slave Unit(s) Set-up All slave units are cabled the same way using coax RG6 or RG11 for back bone. The following section describes the CASCADE features of the Distribution ZHC. CASCADE TOPOLOGY 1. The Master unit produces a 35 dBmV, 1kHz tone at 870 MHz and injects it into the RF stream coming from the Outbound Coax.
Page 12
DISTRIBUTION ZHC SLAVE SET-UP 1. Perform the same procedure for each closet 2. Make sure that the Master is set-up and functioning correctly. 3. Make sure that Coax from Master or lower level cascade(s) are connected 4. Always start with the lowest level cascade in the closet. Power just that unit. When first powered all 3 LED’s on front Panel come on.
If the next highest Slave level in in a different closet, make sure to bring up the closet with the lower Slave level fist Contact Us: If issues arise while performing the install, please contact Z-Band. We will be glad to assist. The number is: 717.249.2606 and press 2 for Engineering. Our business hours are: 8:30-5:00 Eastern Time, Monday-Friday.