Bluworld Water Wonders NSI Slate Assembly Instruction Manual

Advertisement

Quick Links

IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY 
1.
Please check the contents of the boxes before attempting to assemble this product. A full checklist of parts is in this 
instruction booklet. Check it very carefully. In the unlikely event that any components are damaged or missing, please 
contact our customer service hotline at 407‐426‐7674. 
2.
Assemble as near as possible to the point of use. Take extreme care when lifting to avoid personal injury or damage 
to the product.   
3.
This product contains small items and plastic bags. Please be aware of the danger to young children.   
4.
A Pencil, Phillips Screwdriver, Level, and a Measuring Tape will be required for installation.   
ASSEMBLY INSTRUCTIONS 
635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax 407-426-7721
www.bluworldusa.com · shop.bluworldusa.com
Water Wonders NSI Slate™

1-2-3 Installation Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Water Wonders NSI Slate and is the answer not in the manual?

Questions and answers

Summary of Contents for Bluworld Water Wonders NSI Slate

  • Page 1: Installation Instructions

    Water Wonders NSI Slate™ 1-2-3 Installation Instructions IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY  Please check the contents of the boxes before attempting to assemble this product. A full checklist of parts is in this  instruction booklet. Check it very carefully. In the unlikely event that any components are damaged or missing, please  contact our customer service hotline at 407‐426‐7674.  Assemble as near as possible to the point of use. Take extreme care when lifting to avoid personal injury or damage  to the product.    This product contains small items and plastic bags. Please be aware of the danger to young children.    A Pencil, Phillips Screwdriver, Level, and a Measuring Tape will be required for installation.    ASSEMBLY INSTRUCTIONS  635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax 407-426-7721 www.bluworldusa.com · shop.bluworldusa.com...
  • Page 2 Parts  C. Wire Clip B. LED Remote Controller A. LED Light Bar Header D. Pump G. Rock Tray F. Shroud J.Rocks I.Tap Screws and EZ Anchors™ H. Wall Bracket...
  • Page 3 ** It is critical that your waterfall is level as this will ensure even water flow. ** Section 1 ‐ Initial Prepping  Step 1.1 Remove Water Wonders NSI Slate™ from its shipping carton. Step 1.2 Tools required: Level, Pencil, Phillips Screwdriver, Measuring Tape as shown in Fig1.2 as below.
  • Page 4 Step 2.2 Using your measuring tape, measure from the top of your fountain down to the center of your wall bracket and record your measurement. Step 2.3 Using the measurements obtained in Step 2.2, measuring down from the line drawn in Step 2.1, draw vertical line on the wall to indicate the location of the wall bracket sitting position (See Fig 2.3.a).
  • Page 5 Section 3 – Installing the Waterfall  Step 3.1 Locate the Header (E) and Shroud (F). Install the Header (E) by simply sliding into the support rails located behind the fountain as shown in Figures 3.1.a & 3.1.b. Install the Shroud (F) by carefully sliding it behind the panel and down onto the reservoir as shown in Figures 3.1.c and 3.1.d.
  • Page 6 Section 4 – Operating the Waterfall  After filling the fountain with water, plug the LED Light Bar (A) pump into the wall. As Step 4.1 water begins to flow down the surface, guide the water with your hand or use a non-abrasive sponge until the water flows evenly over the entire waterfall surface. It may take a few minutes for the water to cover the entire waterfall surface.
  • Page 7 RF Wireless Touching LED Remote Controller (Brightness Adjusting) 1. Technical Parameters (remote control): a. Power supply: AAA battery*3pcs b. Cover material: ABS c. Fabrication processing: multicolor printing & UV varnish 2. Technical Parameters (controller): a. Working voltage: DC 12V/24V b. Output control: 1circuit c.
  • Page 8 Bluworld, then the Warranty shall be null and void. The Warranty is in effect for a period of six months beginning from the date of sale to the original retail purchaser and the rights under this Warranty are limited to the original retail purchaser.

Table of Contents