Summary of Contents for I-Tech LPC8800
- Page 1 Embedded & Industrial Computing Hardware Platforms for Embedded and Industrial Computing LPC8800 User's Manual ITECH i-Tech Company LLC COMPANY TOLL FREE: (888) 483-2418 • EMAIL: info@itechlcd.com • WEB: www.iTechLCD.com...
- Page 2 About About Overview Acknowledgement Intel, Pentium and Celeron are registered trademarks of Intel Corp. Icon Descriptions Microsoft Windows and MS-DOS are registered trademarks The icons are used in the manual to serve as an indication of Microsoft Corp. of interest topics or important messages. Below is a All other product names or trademarks are properties of description of these icons: their respective owners.
-
Page 3: Table Of Contents
Preparing the Hardware Installation Installing the System Memory Wireless Module Installation 3G SIM Card Installation PCI/PCIe Riser Card Installation On LPC8800-xxB1 with one PCIe slot Installing the Hard Disk On LPC8800-xxB2with 2 PCI slot Connecting Power Wall Mounting Appendix A: Programming System Watchdog Timer... -
Page 4: Chapter 1: Introduction
Introduction Chapter 1: Introduction System Specification Thank you for choosing the LPC8800. The LPC8800 is an 277x(67/89)x194mm Dimensions (WxHxD) upgrade platform of Lanner LPC8800 and features Intel Ivy 1 0 . 9 r x a 5 4 a 5 0 r x 7 . 6 4 ' Bridge i3, i5, and i7 processors. -
Page 5: Package Contents
Chapter 1 Introduction Package Contents Your package contains the following items: • LPC8800 Fanless Embedded System • Serial-ATA/Power Cable (P/N: 080W1N0002001) • Wall-Mounting Kit (P/N: SE9ESA900R100) • Drivers and User’s Manual CD (087W0200V1001) • Power Adapter (P/N: 0P0W075190001) Optional Accessories... -
Page 6: Chapter 2: System Components
Chapter 2 System Components Chapter 2: System Components System Drawing Mechanical dimensions of the LPC8800 Unit: mm 276.4 I— 193.5 J... -
Page 7: Block Diagram
Chapter 2 System Components Block Diagram The block diagram depicts the relationships among the interfaces and modules on the motherboard.. LEK-EA3 -«-»* Processor PCIe Sx DDR3 1 0 6 6 / 1 3 3 3 / 1 6 0 0 P C I e E x p a n s i o n 2K SO- DIMM up to 16GB Far Rtttsr Braird fpir ii^-anar;... -
Page 8: Front Components
Chapter 2 System Components Front Components Description Pin Definition Reference Component F1 HDD (Yellow) and Blinking: data access activities Power LED (Green) Off: no data access activities Power On: The computer is on. Off: The computer is off. F2 Four USB 2.0 Ports An USB type A connector. -
Page 9: Rear Components
R9 Slot for PCIe expansion (*) The PCIe/PCI expansion capability is accomplished via the riser card connected to the system tNote that the driver for these ports should be installed with the following order: Chipset INF->Graphic->Audio * Model LPC8800-xxB2 can support 2 PCI expansion. -
Page 10: Chapter 3: Board Layout
Chapter 3 Board Layout Chapter 3: Board Layout Connectors The following picture highlights the location of the COM port and audio expansion card. Refer to the table 3.1 Connector List for more details. Note: Daughter boards such as COM ports and low-profile PCIe extension boards can only be inserted to the mainboards with the same version. -
Page 11: External Connectors
Chapter 3 Board Layout External Connectors The following picture highlights the location of system input/output connectors. Refer to the table 3.2 Connector List for more details. Board Version VGA1 U$B3 CN4 CN3/ DVID1 LAN1/LAN2 HDMM DCJK1 POWER1 USB1 USB2 LED1 LEB-2280... -
Page 12: Internal Connectors And Jumpers
Chapter 3 Board Layout Internal Connectors and Jumpers The following picture highlights the location of internal connectors and jumpers. Refer to the table 3.2 Connector List for more details. MPCIE2 FAN2 LPC1 CMOS2 Ignitionl 1PCIE1 CMDS1 USB4 COMSLT1 J | COMSLIZJJ SATA PW2 SO-DI... -
Page 13: Internal Connectors And Jumpers (Backside)
Chapter 3 Board Layout Internal Connectors and Jumpers (backside) The f o l l o w i n g picture highlights the location of internal connectors and j u m p e r s o n t h e backside of t h e board. Refer t o the table 3.2 Connector List for more details. -
Page 14: Connectors And Jumpers List
Chapter 3 Board Layout Connectors and Jumpers List The tables below list the function of each of the board jumpers and connectors by labels shown in the above section. The next section in this chapter gives pin definitions and instructions on setting jumpers. Table 3.1 Connector List for LEK-IOA2 Board Pin Definition Reference Labels... -
Page 15: Jumper Settings
Chapter 3 Board Layout Jumper Settings SCT1, SCT2: Select COM1 Protocol Setting SCT2 LEK-IOA2 Board SCT1 Microphone-in Audio Jack (CN1) Pin No. Function CO GND MIC INL CO GND RS-232 INSULATOR MIC INR Line-out Audio Jack (CN2) Pin No. Function CO GND RS-422 LINOUT-L... - Page 16 SPI Rl LEB-2280 Board MIOI on the expansion card: Connector for connecting the COM port and audio expansion board to the LPC8800 main board. Clear CMOS jumper (CMOS1/CMOS2): It is for clearing the CMOS data. CMOS 1 clears CMOS data with real-time...
- Page 17 Chapter 3 Board Layout The controller contains two modes of operation—a Front Panel Function Pin Header (FRONT1): It provides legacy mode using I/O space, and an AHCI mode using LED signal and button function on the front panel. memory space. Software that uses legacy mode will not have AHCI capabilities.
- Page 18 Chapter 3 Board Layout DVI-D Connector (DVID1): A single link DVI-D Connector System FAN Connector (FAN1/FAN2) FAN1 Pin No. Description F A N 2 VCC5 FAN TAC 32 1 PCI/PCIE Expansion connector for PCI or PCIe low Pin No. Description Pin No.
- Page 19 Chapter 3 Board Layout MPCIE1: Mini-PCIe Connector with SIM Card Reader SIGNAL SIGNAL SIGNAL PEG RXN11 Siqnal Siqnal PEG TXN11 WAKE# VCC3.3 PCIE RXN2 PEG RXP11 145 PEG RXN2 PCIE CKN2 PEG TXP11 146 PEG TXN2 VCC1.5 CLKREQ* USIM PWR PCIE RXP2 147 PEG RXP2 UIM DATA...
- Page 20 Chapter 3 Board Layout Ignition Connector on board (ignition 1): Power EnableorDisableDaughterBoardLEK-IOA3(COMSLT1): ignition connector. This jumper is for enabling or disabling the COM3, COM4 ports on daughter board LEK-IOA3. 12 3 4 Pin No. Pin Name Disable Pin No. Pin Name Pin No.
-
Page 21: Chapter 4: Hardware Setup
Portions of the power supply and some internal circuitry remain active until power is removed. 1. Unpower the LPC8800-xxB2 and remove the power cord. 2. Unscrew the 4 threaded screws from the top cover. 3. Open the cover. -
Page 22: Wireless Module Installation
2. Install the riser card to the system by connecting the connectors with the system's PCIEI01 connector. 3. Fix the riser card on the board. 4. Connect the PCIe expansion card to the riser. 5. Fix the card holder back to the system. On LPC8800-xxB1 with one PCIe slot... -
Page 23: Installing The Hard Disk
Note: Using a PCIe or PCI riser card, users have choice of either PCI Express x1 or PCI expansions. i. 1 PCIe is supported on model LPC8800-xxB1 2. 2 PCI are supported on model LPC8800-xxB2 3. Both PCI or PCIe support the Max. Dimension as the following illustrated and the Max. -
Page 24: Connecting Power
Hardware Setup Connecting Power Wall Mounting Connect the LPC8800 to a +9-+30V DC-in power source. The product ships with wall mounting kit. To mount your The DC power-in connector comes with a 2-pin terminal product on the wall, follow the instructions below: block for its Phoenix contact. -
Page 25: Appendix A: Programming System Watchdog Timer
Thus, the processor will be restarted as if a human operator had cycled the power. For sample watchdog code, see watchdog folder under LPC8800 Utility in the Driver and Manual CD R«*t Watchdog Tliwr Executing through the Command Line: Execute the WD.EXE file under DOS (WD.EXE and... -
Page 26: Appendix B: Terms And Conditions
Appendix B Terms and Conditions Appendix B: RMA Service Requesting a RMA# Terms and Conditions 1. To obtain a RMA number, simply fill out and fax the "RMA Request Form"to your supplier. Warranty Policy 2. The customer is required to fill out the problem code as listed. - Page 27 Appendix B Terms and Conditions RMA Service Request Form When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed. Reasons to Return: □ Repair(Please include failure details) R M A N O : Testing Purpose Company: Contact Person:...
Need help?
Do you have a question about the LPC8800 and is the answer not in the manual?
Questions and answers