Table of Contents
Advertisement
Quick Links
HomeTroller Zee Quick-Start Guide
your internet router.
c) Connect the Z-Stick to one of the USB ports on your HomeTroller Zee
d) Connect the AC power adapter to your HomeTroller Zee to begin the boot process. Allow the unit to boot fully
(about 1 minute and 45 seconds).
Accessing the HomeTroller Zee Web Interface
Once the unit boots, you'll need to access the web interface to
set the system up. The method below should work with any
browser on any device (mobile or desktop).
a) Navigate to
http://find.homeseer.com
b) Click the "Search" button. Your HomeSeer system
should now appear at the bottom.
c) Click the IP address hyperlink to access your system's
web interface.
Set Your System Password
The system password screen will appear the first time you run your HomeTroller
to prevent unauthorized access to your unit.
Activate and Register Your HomeTroller Zee Online
Be sure to activate your HomeTroller Zee and register the unit to receive HomeSeer support. To do this, make you're
your unit is connected to the internet and follow these steps:
a) From the HomeTroller Zee web interface, use the pull down menus to navigate to the General Tab of the Setup
Area (TOOLS > Setup)
b) Click the "Register Online" button in the License section of the Setup screen and enter your license codes.
Note: License codes are included on a sticker on the bottom of your HomeTroller Zee.
Setting the Time Zone and Updating Your HomeTroller Zee
Be sure to set the time zone and check for updates and install any that are available. To do this, follow these steps:
a) Access the General Tab of the Setup Area again and scroll to the "Location" area. Find the Time Zone field and
change that to time zone where your HomeTroller Zee is installed.
Congratulations on your purchase! Your HomeTroller Zee is ready to put you in
control of your home. Please take a few minutes to read through this guide to
familiarize yourself with the steps required to set up your Z-Wave network and your
HomeTroller Zee.
STEP #1
– HomeTroller Zee Initial Setup
After you've created your Z-Wave network, you'll need to install your HomeTroller
Zee. Follow these steps:
HomeTroller Zee Hardware Installation
a) Unpack the HomeTroller Zee, Ethernet cable and AC power supply.
b) Connect the Ethernet cable to your HomeTroller Zee and to a network port on
Please do this now by following the prompts on your screen.
Page 1
Zee. You MUST set a system password
Example: US – America/New_York
Advertisement
Table of Contents
Related Manuals for HomeSeer Technologies HomeTroller Zee
Summary of Contents for HomeSeer Technologies HomeTroller Zee
- Page 1 Connect the Z-Stick to one of the USB ports on your HomeTroller Zee d) Connect the AC power adapter to your HomeTroller Zee to begin the boot process. Allow the unit to boot fully (about 1 minute and 45 seconds).
- Page 2 From the HomeTroller Zee web interface, use the pull down menus to navigate to the General Tab of the Setup Area (TOOLS > Setup). If an update is available, click the update button near to top of the page and wait for the update to download and install.
- Page 3 Simply put, an automation event consists of an action (or actions) that are set into motion by one or more triggers. Example: Turning on lights at sunset. Trigger = sunset, Action = turning lights on. With HomeTroller Zee, you can quickly and easily create all the events you need.
- Page 4 2. Navigate to the PLUG-INS > Manage page and disable the X10 and Z-Wave plug-ins. 3. Detach the X10 and Z-Wave interfaces from your HomeTroller Zee. Leave these detached until prompted to reattach below. 4. Navigate to the TOOLS > System > Restart System page and click the [Restart...] button to restart your HomeTroller Zee.
- Page 5 f) Now that HSTouch Sever is installed we will need to enable it. Underneath the Enable column click on the red toggle. It should become green with a check mark in it. g) HSTouch Server is now enabled. You can now go into HSTouch on your device to configure HSTouch. STEP #8 –...
- Page 6 k) Now that your Client has been set up, go back to the Main Screen and go to the settings menu on the bottom right. Click Exit. Now go to your app drawer and click HSTouch. This will allow for any changes to take place. You are now ready to control your home via your device! Icon Legend for HS3 This is a list of the icons that are found in HS3 with a description of their function.
- Page 7 Into Z-Wave Network Device Failure Replace Device Z-Stick Failure Contact Homeseer Hometroller Zee Not Powered On Power Unit On Hometroller Zee Not Fully Booted Wait 2 Minutes For Unit To Boot HSDiscover Cannot Locate Device Hometroller Zee Not Connected To Connect Unit To Router And Reboot Door Locks Won’t Include Or Can’t...
Need help?
Do you have a question about the HomeTroller Zee and is the answer not in the manual?
Questions and answers