Summary of Contents for Chloride FS11007A-S3SB FilterPro
- Page 1 Secure Power Always Chloride FilterPro™ Power Filter (7 Amps) FS11007A-S3SB FilterPro Installation handbook...
-
Page 2: Registering Your Product
Secure Power Always FilterPro Power Filter Introduction Thank you for selecting this Chloride product. Chloride’s FilterPro Power Filter offers reliable protection from the harmful effects of electrical line disturbances. Registering your product To register your FilterPro Power Filter, please complete the warranty registration card included with your filter or online at www.chloridepower.com/usa. -
Page 3: Installation Instructions
FilterPro Power Filter Installation instructions CAUTION: Indoor use only. Install in a protected environment. Position the FilterPro where desired, desktop or wall-mount. NOTE: When mounting the FilterPro on the wall or any other surface, it can be positioned in any direction. Position the Filter Pro where desired. - Page 4 Secure Power Always FilterPro Power Filter Install the two # 8 or # 10 wall mounting screws at one end of the mounting area, leaving 1/8” clearance between the screw head and the surface. Place the FilterPro in position, and install the other two wall mounting screws. Tighten down all 4 wall mounting screws to secure the FilterPro.
-
Page 5: Overcurrent Protection
U.S. National Electric Code and local electrical codes. If the red Wiring Fault LED remains illuminated, contact a qualified electrician to identify any wiring discrepancies. Chloride recommends using electrical testing equipment to verify proper electrical wiring. Filter Disposal Once your filter has reached the end of its useful life and it is necessary to dispose of the unit. -
Page 6: Warranty
Except as set forth herein and except as to title, there are no warranties, express or implied, or any affirmations of fact or promises by Chloride for the products, their merchantability, or fitness for any particular purpose. In no event shall Chloride be liable for lost profits, goodwill, or any other special or consequential damages. -
Page 7: Specifications
FilterPro Power Filter Specifications Specification Part number FS11007A-S3SB Electrical Topology TVSS with filter Voltage (V) Frequency (Hz) Current - max/continuous RMS (Amps) Overcurrent protection push-to-reset circuit breaker Input (six foot attached cord) 5-15P Output (six inch attached cord) (3) 5-15R Efficiency ≥... - Page 8 Secure Power Always FilterPro Power Filter Specification Safety listings 1449, 1283, 1363 Part 68, EMC N/A Physical Indicators (LED) power available (green), wiring fault (red) Dimensions HxWxL - in (mm) 2.7 x 3.9 x 9.9 (69 x 99 x 252) (with bracket) Dimensions HxWxL - in (mm)
- Page 9 Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If you experience trouble with this telephone equipment, please contact Chloride at (800) 327 8801 for information on obtaining service or repair. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is resolved.
- Page 10 Secure Power Always FilterPro Power Filter Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your site has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment.
- Page 11 F: +65 6481 0552 Vietnam www.chloridepower.co.uk www.chloridepower.com.sg T +84 8 255 6737 F +84 8 255 6800 www.chloridepower.com/vn FilterPro is a trademark of Chloride. All other trademarks are the property of their respective companies. © 2009 Chloride 913-636 @ Rev. A...
Need help?
Do you have a question about the FS11007A-S3SB FilterPro and is the answer not in the manual?
Questions and answers