superbrightleds UBL-RGB120 User Manual

Important: Read all instructions prior to installation.
Underwater RGB LED Boat Light

Features

316L Marine Grade Stainless Steel
Poly-Carbonate Lens
5 Ft Power Wire (18AWG)
Specifi cations
120W RGB LED Underwater Boat Light
Input Voltage
Current Draw
Total Power Consumption
Operating Temperature
LED Lifetime
LED Brand
Warranty
Dimensions
Weight

Parts Included

Underwater Boat Light
1- (UBL-RGB120)
2- M5 Machine screws
2- M5 Flat washers
2 - M5 Locking Nuts
2 - M5 Self Tapping screws
2- Neoprene washers

Recommended Tools (not included)

Drill and Drill Bits
#2 Phillips Screwdriver
Heavy Grit Sandpaper
Isopropyl/Denatured Alcohol
Pencil (Wax Pencil recommended for fi berglass)
Caution
LIGHTS MUST BE SUBMERGED TO AVOID OVERHEATING. USE OUT OF
WATER WILL DECREASE LED LIFETIME AND CAUSE EARLY FAILURE.
LIGHTS HAVE OVER TEMPERATURE PROTECTION (FOR TESTING
PURPOSES ONLY) AND WILL SHUT OFF WHEN MAX TEMP (194 F / 90 C)
IS REACHED. DO NOT OPERATE LIGHTS OUT OF WATER FOR MORE
THAN 2 MINUTES FOR TESTING. LIGHTS WILL BE HOT IF OPERATED
OUT OF WATER FOR EXTENDED PERIODS. INSTALLATION OF LIGHTS
MUST BE DONE WHILE BOAT IS OUT OF WATER AND DRY. SBL IS NOT
RESPONSIBLE FOR ANY INJURY OR PROPERTY DAMAGE INCURRED
DUE TO IMPROPER INSTALLATION.

Installation Instructions

TIP: Know your hull; most common type is fi berglass.
Wood, metal and carbon fi ber are other less common hull types.
For metal or carbon fi ber hull, fi rst be sure to mount an insulating
material between metal or carbon fi ber surfaces and lights to
prevent galvanic corrosion.
If uncertain about type of hull, please contact boat manufacturer
for assistance.
Over-Temp Protection
Waterproof IP68
9 ~ 15 VDC
8.0 A @ 13.5VDC
108W @ 13.5VDC
-22°F~122°F (-30°C~50°C)
50,000 Hours
CREE
3 Years
Dia. ø 3.69in (9.4cm),
Thickness 0.67in (1.7cm )
1.43 lb (0.65kg)

Recommended Accessories

Multi Zone Controller with Remote
(LDRF-RGB-MZ)
Additional Controller (RGB-MZ)
Additional Remote (MZ-RGB-REMOTE)
Mounting Bracket (UBL-MB2)
Lint Free Cloths
Masking Tape
Marine Sealant
Installation Instructions
1. Determine desired mounting location on boat's transom.
Be sure to check actual draft water level if operating LED
lights at speed. (See Diagram Below)
Recommended mounting depth between 6-8" below
waterline for best eff ect. Be sure that mounting location is
free of any obstructions before drilling through hole. Mark
center of desired location.
2. Drill 1/4" through hole in center of desired location and
feed power wire through hole into boat. Hold light fl ush
against transom, mark location for mounting screws, then
remove light.Drill pilot holes for mounting screws to prevent
cracking in fi berglass hulls.
3. Use heavy grit sandpaper to rough up the surface and to
remove any debris from drilling. Clean area using alcohol
and lint free cloth.
4. Apply uniform layer of marine sealant to back side of light,
especially around mounting holes and wire connection.
Also apply marine sealant to transom surface around pilot
and through holes.
5. Feed power wire back through 1/4" hole into boat and
press light against transom using uniform pressure. Install
mounting screws with included neoprene washers and
tighten light to transom.
6. Use sealant that has squeezed out from beneath light to
create complete seal around outer edge of light. Remove
any excess sealant.
7. Connect Black (positive) wire from Light to V+ on
Controller. Connect remaining negative wires from Light to
Controller. Connect Red to R, Green to G and Blue to B.
8. Connect positive (RED) wire to positive battery terminal
through fuse to switch (see diagram below). Connect
negative (BLACK) wire to negative battery terminal. Marine
grade heat shrink butt connectors and ring terminals are
recommended.
9. Ensure light is solidly attached to hull and that marine
sealant has fully cured prior to putting boat in water.
Lights may be tested briefl y while out of water. Lights will
overheat and shut down if operated out of water for more
than testing.
4400 Earth City Expy, St. Louis, MO 63045
User Manual
Part Number:
UBL-RGB120
WIFI-CON
866-590-3533 superbrightleds.com