Advertisement
Limited Lifetime Warranty
NVT warrants that the product conforms to NVT's applicable published
specifications and is free of defects and workmanship, for the life of
the product.
There shall be no other warranties, express, statutory or otherwise,
including any implied warranty of merchantability of fitness or any
other obligation on the part of NVT with respect to any of the products.
In the event that any product is damaged or altered or modified
without the express written consent of NVT, any warranty for those
products will cease and NVT will have no further liability as it pertains
to those products. NVT assumes no responsibility for damages or
penalties incurred resulting from the use of this product in a manner
or location other than for which it is intended.
NVT's liability under any warranties shall be discharged by replacing
or repairing any part or parts which do not conform to the applicable
warranty under normal and proper use. NVT's liability with respect to
any product shall not exceed a refund of the price received by NVT for
that product, and in no event shall NVT have any liability for any
incidental, consequential, special, or indirect damages.
Some states do not allow the exclusion or limitation of special, incidental
or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Customer Support
If you are experiencing problems, attempt to simplify your setup. Test
each cable segment separately. For example, test the camera and
monitor together without the other equipment. Then add in the NVT
transceivers, back-to-back. Test each segment of a long cable-run
independently. Attempt to isolate the problem.
NVT customer support is available for consultation from 8:00 AM to
5:30 PM PST Monday through Friday. In addition, emergency after-
hours callback support is available.
US Office:
(+1) (650) 462-8100
US Fax:
(+1) (650) 326-1940
UK Office:
(+44) (0)20 8977 6614
UK Fax:
(+44) (0)20 8973 1855
Email USA:
www.nvt.com/email
Email UK:
www.nvt.com/email
Web home page:
www.nvt.com
Returns
Please call before returning units to NVT. Returned materials must
have a "Returned Materials Authorization" (RMA) number from NVT
marked on the outside of the shipping carton.
Agency
These NVT products are listed and/or conform to the following
certifications and directives:
RoHS
UL Listed to UL2044 or UL/IEC 60065.
cUL Listed to CAN/CSA22.2 No. 1 for Canada.
CE Mark under EMC and low voltage
Complies with FCC part 15B limits
Directives for the European Union.
Power-Video-Data 4-Channel Application using the NV-704J-PVD at the Telecommunications Closet or IDF
Power-Video-Data at the Camera End
1. Connect the NV-216A-PV or the NV-218A-PVD as shown in the examples on the other side.
2. Connect the 4-pair Cat5 UTP cables coming from the cameras into the appropriate camera port on the NV-704J-PVD using the RJ45 connector as shown in Figure 4 (previous page).
3. Connect the outputs of your independent power supply into the appropriate Camera Power terminals on the NV-704J-PVD. Torque to 2 in-lbs (0.22 Nm). NVT recommends the use of 18AWG (1,0 mm)
solid conductor wire. NVT also recommends that the external power supply have individually floating outputs.
Power-Video-Data at the Equipment Room End
4. Connect the NV-704J-PVD's Control Room outputs to the NV-413A or NV-452R via UTP using RJ45 connectors and Cat5 cable. The control end pinouts are listed in Figure 5 (previous page). If P/T/Z
telemetry is required, connect a second RJ45 Cat5 cable from the data port to the DVR's RS-422 or RS-485, control output.
Power-Video-Data 16-Channel Application using the NV-716J-PVD at the Telecommunications Closet of IDF
Power-Video-Data at the Camera End
1. Connect the NV-216A-PV or the NV-218A-PVD as shown in the examples on the other side.
2. Connect the 4-pair Cat5 UTP cables coming from the cameras into the appropriate camera port on the NV-716J-PVD using the RJ45 connector as shown in Figure 4 (previous page).
3. Connect the outputs of your independent power supply into the appropriate Camera Power terminals on the NV-716J-PVD. Torque to 2 in-lbs (0.22 Nm) Figure 5 (previous page). NVT
recommends the use of 18AWG (1,0 mm) solid conductor wire. NVT also recommends that the external power supply have individually floating outputs.
Power-Video-Data at the Equipment Room End
4. Connect the NV-716J-PVD's Control Room outputs to the NV-1613, NV-1613S, NV-1662 or NV-1672 via UTP using RJ45 connectors and Cat5 cable. See the NV-716J-PVD wiring
diagram above. If P/T/Z telemetry is required, connect additional RJ45 Cat5 cable(s) from the data port(s) to the DVR's RS-422 or RS-485 Code Converter (alternately known as a
data distribution unit or fan-out unit.) Additional details can be found at www.nvt.com.
Camera Connections
NV-716J-PVD Wiring Diagram
Channel 1
Channel 2
Channel 3
1 Video 1+
1 Video 2+
1 Video 3+
2 Video 1-
2 Video 2-
2 Video 3-
3 Data A +
3 Data A +
3 Data A +
4 Power 1-
4 Power 2-
4 Power 3-
5 Power 1+
5 Power 2+
5 Power 3+
6 Data A -
6 Data A -
6 Data A -
7 Power 1+
7 Power 2+
7 Power 3+
8 Power 1-
8 Power 2-
8 Power 3-
Channel 9
Channel 10
Channel 11
1 Video 9+
1 Video 10+
1 Video 11+
2 Video 9-
2 Video 10-
2 Video 11-
3 Data C +
3 Data C+
3 Data C+
4 Power 9-
4 Power 10-
4 Power 11-
5 Power 9+
5 Power 10+
5 Power 11+
6 Data C -
6 Data C -
6 Data C -
7 Power 9+
7 Power 10+
7 Power 11+
8 Power 9-
8 Power 10-
8 Power 11-
Control Room Connections
Channel 1-4
Channel 5-8
Channel 9-12
1 Video 2+
1 Video 6+
1 Video 10+
2 Video 2-
2 Video 6-
2 Video 10-
3 Video 3+
3 Video 7+
3 Video 11+
4 Video 1-
4 Video 5-
4 Video 9-
5 Video 1+
5 Video 5+
5 Video 9+
6 Video 3 -
6 Video 7 -
6 Video 11 -
7 Video 4+
7 Video 8+
7 Video 12+
8 Video 4-
8 Video 8-
8 Video 12-
Figure 7 Control End Pinouts (NV-716J-PVD)
Channel 4
Channel 5
Channel 6
1 Video 4+
1 Video 5+
1 Video 6+
2 Video 4-
2 Video 5-
2 Video 6-
3 Data A +
3 Data B +
3 Data B +
4 Power 4-
4 Power 5-
4 Power 6-
5 Power 4+
5 Power 5+
5 Power 6+
6 Data A -
6 Data B -
6 Data B -
7 Power 4+
7 Power 5+
7 Power 6+
8 Power 4-
8 Power 5-
8 Power 6-
Channel 12
Channel 13
Channel 14
1 Video 12+
1 Video 13+
1 Video 14+
2 Video 12-
2 Video 13-
2 Video 14-
3 Data C+
3 Data D +
3 Data D+
4 Power 12-
4 Power 13-
4 Power 14-
5 Power 12+
5 Power 13+
5 Power 14+
6 Data C -
6 Data D-
6 Data D-
7 Power 12+
7 Power 13+
7 Power 14+
8 Power 12-
8 Power 13-
8 Power 14-
Channel 13-16
Data/Telemetry
1 Video 14+
1 Data B+
2 Video 14-
2 Data B-
3 Video 15+
3 Data C+
4 Video 13-
4 Data A-
5 Video 13+
5 Data A+
6 Video 15-
6 Data C-
7 Video 16+
7 Data D+
8 Video 16-
8 Data D-
Channel 7
Channel 8
1 Video 7+
1 Video 8+
2 Video 7-
2 Video 8-
3 Data B +
3 Data B +
4 Power 7-
4 Power 8-
5 Power 7+
5 Power 8+
6 Data B -
6 Data B -
7 Power 7+
7 Power 8+
8 Power 7-
8 Power 8-
Channel 15
Channel 16
1 Video 15+
1 Video 16+
2 Video 15-
2 Video 16-
3 Data D+
3 Data D+
4 Power 15-
4 Power 16-
5 Power 15+
5 Power 16+
6 Data D-
6 Data D-
7 Power 15+
7 Power 16+
8 Power 15-
8 Power 16-
Copyright (c) 2011 NVT, Inc. 451-218-1-H
08/11
Advertisement
