Advertisement
Quick Links
G
W
ear
aGon
G
W
ear
aGon
Read the owner's manual over carefully before you begin using your trailer. You will need
this manual for the safety warnings and precautions, operating procedures, parts list,
inspection, and maintenance information. Keep this manual for continued reference.
Copyright © 2007 - 2012 Let's Go Aero, Inc.
125
™
Sport Utility & Performance Trailer
125 C
™
amper
Read this owner's manual carefully before
you begin using your Trailer.
S
u
& O
afe
Se
peraTiOn
G
W
125 S
ear
aGOn
pecificaTiOnS
G
W
125 c
ear
aGOn
aMper
f
& O
eaTureS
peraTiOn
i
, M
nSpecTiOn
ainTenance
c
and
leaninG
T
l
railer
icenSinG
W
/ r
p
arranTy
epair
rOcedureS
S
ave
Models GW 1125 & GW 1125-GL
T
M
hiS
anual
User Manual
pg. 3
pg. 4
pg. 6
pg. 12
pg. 16
pg. 16
™
Advertisement
Summary of Contents for LetsGoAero GW 1125
- Page 1 User Manual Models GW 1125 & GW 1125-GL ™ Sport Utility & Performance Trailer aGon ™ 125 C ™ aGon amper Read this owner’s manual carefully before you begin using your Trailer. pg. 3 & O peraTiOn pg. 4 125 S aGOn pecificaTiOnS 125 c aGOn aMper pg.
- Page 3 • Verify that endgate is secured by properly closing draw latch. • Verify that the lid is secured using elastomer draw latch and pin locks furnished. GW 1125-9/12 – 3 –...
- Page 4 The Stabilizer swing arm secures in reclined position for transit. Pull arm away to release from notched position in order to operate in downward position for trailer support. To adjust swing arm height, simply adjust arm length by pressing the release latch on the arm. – 4 – GW 1125-9/12...
-
Page 5: Opening And Closing
Be sure that lock is engaged after removing key (pull on lock). WARNING Lock down lids using either one or both pin locks before transit. Failure to do so may result in property damage under extreme road or weather conditions. GW 1125-9/12 – 5 –... - Page 6 Solar powered ventilator removes condensation from accumulating during the night and provides quiet, reliable ventilation. Moves 1,000 cubic feet per hour, will run for up to 48 hours without sunlight. Also prevents mold and mildews. – 6 – GW 1125-9/12...
- Page 7 To prepare for transit, release adjustment lever to minimize leg length and fold upward to retracted, catched position shown above. WARNING: Always fold up Leveler Kit in secure position before operating trailer. Do not move trailer with stabilizers down, or damage will occur. GW 1125-9/12 – 7 –...
- Page 8 Be sure to install correctly, as each panel’s length is designed for its spe- Be sure to install correctly, as each panel’s length is designed for its spe- cific location in the sequence. cific location in the sequence. – 8 – GW 1125-9/12...
-
Page 9: Installation
Bar in the process (this portion of the tent will wrap around the outside of the trailer’s base). Connect outside bungee by connecting the two hooks located on each end of the tent wrap. Finish velcro wrap inside and outside by overlaying the two velcro ends. GW 1125-9/12 – 9 –... - Page 10 Connect vestibule cover snaps located underneath lowered endgate. Connect peak tubes and insert into vestibule’s center sleeve. Slip end through holder as shown (rubber end for contact with lid). – 10 – GW 1125-9/12...
- Page 11 Place the SolarVent in direct sunlight (the vent can work without batteries, but will only ventilate during sunlight hours). Consult SolarVent manual by ICP Solar Technologies furnished with your trailer for more information. GW 1125-9/12 – 11 –...
-
Page 12: Inspection, Maintenance, And Cleaning
3. Carefully tap the new bearing cup into the hub making sure the cup is seated against the bottom of the bore. & i earinG eplaceMenT nTerchanGe Axle # of Spindle Inner Bearings Outer Bearings Capacity Bolts Type Cone Cone 1000# - 2500# 4 or 5 Straight L44610 L44643 L44610 L44643 – 12 – GW 1125-9/12... -
Page 13: Bearing Lubrication
6. Bend the legs of the cotter pin over the top of the spindle to ensure the spindle nut will not back off. 7. The spindle nut should be free to move with your fingers with only the cotter pin holding it in place and the hub should not have noticeable movement when pulled back and forth. GW 1125-9/12 – 13 –... - Page 14 Wheel nuts and bolts are offered in different cone angles (usually 60° or 90°). It is important to match the angle of the fastener to the wheel on the axle. – 14 – GW 1125-9/12...
- Page 15 Toe Wear Incorrect toe-in Align at alignment shop Cupping Out-of-balance Check bearing adjustment and balance tires Avoid sudden stops when possible and adjust brakes Flat Spots Wheel lockup and tire skidding GW 1125-9/12 – 15 –...
- Page 16 Possible to Reduce the Size of the Main Frame Members )Reduces Cost and Weight) Added Strength Retards Frame Twisting Assured Proper Fit Eliminates Down Time and Rework/Repair High Quality Standards Outstanding Quality Control of Components Reduces Maintenance and Repair – 16 – GW 1125-9/12...
- Page 17 1. An RMA (Return Merchandise Authorization) is required for any return of product for warranty work of defective components. Contact Let’s Go Aero for an RMA, phone 719-630-3800, or via email to contact@letsgoaero.com. Freight must be prepaid – collect shipments will be refused. Include your RMA number, name, return address, phone number and a description of the problem.
Need help?
Do you have a question about the GW 1125 and is the answer not in the manual?
Questions and answers