Do you have a question about the Spirit and is the answer not in the manual?
Questions and answers
Summary of Contents for Hydro Massage Products Spirit
Page 1
Hydromassage Products Owner’s Manual & Installation Guide IMPORTANT: Read all instructions before proceeding with installation. INSPECT entire unit to ensure it is not damaged and is the correct model, size and color. Verify it has all the features and options originally ordered. All whirlpools MUST BE TESTED before or during rough installation.
Congratulations On the purchase of your Hydromassage bath tub! Hydromassage Products supports your purchase with strong commitment to quality and customer satisfaction. Please read and follow all of the instructions contained in this Owner’s Manual before installing, operating or maintaining your whirlpool. In addition, you should refer to these instructions during the life of your whirlpool.
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING: When using this unit, basic precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS DANGER — To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times.
INSTALLATION INSTRUCTIONS WARNING: Verification of Electrical requirements MUST be made before installation. Refer to the Pump label for Voltage and frequency requirements. INSTALLATION 1. Unpack the contents carefully and inspect the bath to verify that it is the correct model, features, and color, the pump is the correct size ordered and check for visible defects or damage.
Page 5
INSTALLATION INSTRUCTIONS [continued] WARNING: Whirlpool pump and piping are factory assembled. Relocation of pump or other modifications could adversely affect the performance and safe operation of this whirlpool. Hydromassage Products shall not be liable under its warranty or otherwise for personal injury or damage caused by such unauthorized modification.
Page 6
STRUCTURAL PREPARATION: 1. Literature dimensions are for reference only. Installation dimensions should be taken directly from the tub. An Access panel of 18” x 18” minimum must be provided at the pump end of the whirlpool. Allowing sufficient clearance to make final connections and for servicing the pump and power panel. Access may be through the wall or platform apron at the end of the unit.
Page 7
Typical Methods of Sealing & Finishing Make sure interior of tub is protected during finishing 1A Drop In, Island or 1C Integral Tile Flange with or Sunken Installation 1D Attached Tile Flange without Integral Skirt Installation INTEGRALLY SKIRTED AND/OR FLANGED WHIRLPOOLS Installation Procedures: IMPORTANT!!! Before installation begins, make sure that:...
When selecting fill spout location, check to ensure that the Model spout is long enough to clear the tub rim from its desired loca- Spirit 1" 8" tion. If installation is to be on the tub deck, check the backside Mystique jr 1 1/2"...
Page 9
Electrical Installation: WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED, LOCALLY CERTIFIEDELECTRICIAN. IN ACCORDANCE WITH THE REQUIRMENTS OF THE NATIONAL ELECTRICAL CODES AND PROCEDURES. WARNING: WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER: RISK OF ELECTRICAL SHOCK!! This unit REQUIRES one or more dedicated cir- cuits, protected by a GROUND FAULT CIRCUIT INTERRUPTER (GFCI).
OPERATING INSTRUCTIONS This manual contains all the information needed for the proper operation of this Whirlpool Bath. WARNING: BEFORE OPERATING REFER INSTRUCTIONS PERTAINING TO THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS ON THE LAST PAGE OF THIS MANUAL. CAUTION DO NOT OPERATE THIS UNIT WITHOUT THE GUARD COVER OVER THE SUCTION FITTING.
Page 11
The effects of Hyperthermia include: a) Failure to perceive heat b) Failure to recognize the need to exit the Hydromassage bathtub c) Unawareness of impending hazard. d) Fetal damage in pregnant woman f) Physical inability to exit the hydromassage bathtub, and g) Unconsciousness resulting in the danger of drowning.
Operating Instructions For Bronze, Silver, and Gold series Whirlpools For Bronze, Silver, Gold and Aromassage series whirlpools WHIRLPOOL USER INFORMATION – PLEASE NOTE: The whirlpool action may cause even small amounts of bubble bath or shampoo to foam excessively. Exercise moderation in experimenting with different soap products and follow the whirlpool system cleaning instructions.
Operating Instructions For Platinum series whirlpools NOTE: Do not start pump until all jets are submerged water level should be 3" above highest jet. Dual on/off air button control operates each pump/jet action independently. Press the button once and the pump will turn on. Press the button again and the pump will turn off.
Page 14
OPERATING INSTRUCTIONS This manual contains all the information needed for the proper operation of Air Bath Systems. WARNING: BEFORE OPERATING REFER INSTRUCTIONS PERTAINING TO THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS ON THE LAST PAGE OF THIS MANUAL. TO OPERATE 1.
Page 15
Continued WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. WARNING: Flush the whirlpool system periodically. See user maintenance instructions. USER MAINTENANCE INSTRUCTIONS CARE AND CLEANING To assure a long lasting "like-new" look to your hydromassage bathtub we recommend the following easy care procedures: 1.
AIR MASSAGE SERIES AIRBATHS Aromassage series Airbaths #1.1st press: The blower starts at maximum speed, LED: ON #1 #2 #3 #4 2nd press: The blower stops, LED: ON until the purge cycle stops. Approximately 20 minutes. #2.1st press: Speed goes up, LED ON when pressing Release pressure at the desired speed.
Page 17
Neck Massage pillow Turning the dial clockwise will reduce the pillow jet pressure down to 5% *Before operating the Neck Massage pillow, make sure the white lycra pillow cover is covering the gray pillow. Underwater mood light on/off air button: Press the button once and light turns on Press the button again and the light turns off Bulb replacement:...
Page 18
INLINE MAINTENANCE HEATER WIRING AND OPERATING INSTRUCTIONS The whirlpool heater is totally self-contained to insure trouble free operation. Once the whirlpool heater is wired, and the unions are tightened, operation is automatic. The heater will maintain the temperature of the water in the bathtub.
Page 19
Maintenance of Whirlpool system and acrylic surface Maintenance of Whirlpool system and acrylic surface Initial Cleaning Initial Cleaning Before tub is used, the whirlpool system should be cleaned out and disinfected. Remove all debris Before tub is used, the whirlpool system should be cleaned out and disinfected. Remove all debris and clean tub before putting the whirlpool into service.
Warranty Service. In order to obtain service provided under this warranty during regular business hours, USE SUCH PRODUCT, EVEN IF HYDROMASSAGE HAS BEEN ADVISED OF THE POSSIBLITY OF contact the dealer or distributor who sold the unit, or Hydro Massage Products directly at 1-888-409-8860. SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
Troubleshooting guide Pump Motor Does Not Start Leak at Pump 1. Shaft seal leaking 1. GFCI or circuit breaker in off position Contact service technician. Check circuit breaker panel or GFCI outlet where pump is plugged in to verify power source. 2.
Hydromassage Products Product Registration Information and Warranty Confirmation ATTENTION: To ensure that your warranty is registered and confirmed with the manufacturer, please take a few moments to complete, sign and return the Product Registration Card provided below within 30 days of the date of purchase. WARRANTY CONFIRMATION: By returning this Product Registration Card, we can confirm the date of purchase for your new product.
Need help?
Do you have a question about the Spirit and is the answer not in the manual?
Questions and answers