Streetwize SWPB3 Instructions

Emergency jumpstarter & portable power bank

Advertisement

SWPB3 Manual 2018 AW.qxp_Layout 1 15/01/2018 20:50 Page 2
Emergency Jumpstarter
& Portable Power Bank
12V - 240V
600Amp
Emergency Jumpstart & Power Bank contents:
Emergency Jumpstarter & Power Bank Unit
12V Smart Jumpstart Cables
(protects jumpstarter
vehicle battery).
USB charge cable with 4 built-in
assorted adaptors.
240V mains plug.
12V in-car charging plug.

Emergency Jumpstart Operating Instructions:

The unit can jump start vehicles with a absolute minimum of 30%. However for
optimum performance fully charge the unit (100%). NEVER USE THIS PRODUCT TO
JUMPSTART WITH LESS THAN 30% POWER SHOWING AS THIS CAN CAUSE
PROBLEMS AND DAMAGE THE PRODUCT.
1. Connect the crocodile clips in the following order. Positive (+ Red) charging lead to the
positive (+ Red) terminal. Connect the negative (- Black) charging lead to the negative
(- Black) terminal. It is important that the crocodile clips are making good contact with
the battery terminals.
2. Connect the crocodile clips into the Jumpstarter power outlet turn the switch to ON &
press the round power button The .
3. Turn the key to start the vehicle engine in NO longer than 4 second bursts. If the engine
does not start immediately turn off the engine, wait at least 15 seconds, if the vehicle
does not start after 3 attempts it could mean that the battery is damaged or another
function of the vehicle is at fault and should be checked by a qualified auto mechanic.
4. When the vehicle starts, IMMEDIATELY, press the round power button on the unit until
the display is off, then turn the switch to OFF. Unplug the smart jumpstart cable from
the unit and remove the crocodile clips from the battery.
Caution: Never connect the red & black crocodile clips together.
Never use near a naked flame. Store in a cool dry place. DO NOT use or store at
temperatures above 50°C or below -10°C.
Please READ & UNDERSTAND the instructions carefully before
operating this device, and retain for future reference.
It is recommended to charge the unit for at least 3 hours
before any use.
SWPB3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SWPB3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Streetwize SWPB3

  • Page 1 SWPB3 Manual 2018 AW.qxp_Layout 1 15/01/2018 20:50 Page 2 SWPB3 Emergency Jumpstarter & Portable Power Bank Please READ & UNDERSTAND the instructions carefully before 12V - 240V operating this device, and retain for future reference. 600Amp It is recommended to charge the unit for at least 3 hours before any use.
  • Page 2 SWPB3 Manual 2018 AW.qxp_Layout 1 15/01/2018 20:50 Page 3 Function on Smart Battery Cable (LED on unit. 1) Reverse polarity connection: Solid Red LED with fast 2 short beep,. 2) Short-circuit protection: Solid Red LED with long beep. 3) Over-heat protection: Solid Red LED with long beep (with a lower tone).
  • Page 3 SWPB3 Manual 2018 AW.qxp_Layout 1 15/01/2018 20:50 Page 4 Charging smart phones etc: 1. Insert the USB charging plug into any of the 3 – 5V 2.1A or 1.0A USB output ports. 2. Insert the correct adaptor for the device to be charged.
  • Page 4 SWPB3 Manual 2018 AW.qxp_Layout 1 15/01/2018 20:50 Page 1 Warnings: The power bank will generate heat when charging. Use it in a well ventilated area when charging. Keep the power bank away from heat sources, direct sunlight, humidity, water or other liquids.

Table of Contents