Do you have a question about the 579-84-215 and is the answer not in the manual?
Questions and answers
Summary of Contents for Young America Baby 579-84-215
Page 1
Association and the CPSC-Consumer Product Safety Commission. Thank you for purchasing a Young America Baby ™ Crib. If you find that you ™ are missing a part or if a part is defective in any way, contact your Young America Baby retailer for assistance.
Page 2
WARNING: FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH. Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. • Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges.
Page 3
IDENTIFYING THE PARTS LEFT CRIB END WITH DRAWER GUIDE RIGHT CRIB END DROP SIDE WITH DRAWER GUIDE STATIONARY SIDE CRIB SPRING (1) WITH STABILIZER RAILS (2) SCISSORS BRACKETS (4) LEFT & RIGHT CRIB DRAWER DRAWER BOTTOMS (2) DRAWER DIVIDER (1) SIDES WITH GUIDES (2) CRIB DRAWER FRONT (1) CRIB DRAWER BACK (1)
Page 4
IDENTIFYING THE HARDWARE Identify the hardware included in the hardware bag using the illustrations below 4 Decorative bolts 4 Casters w/brakes " ( " x 20 thread) 6 Decorative bolts " ( " x 20 thread) 1 Allen wrench 4 Bolts, 8 washers & and 4 nylon locking nuts "...
Page 5
ASSEMBLING AND OPERATING YOUR CRIB NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE REFERENCE. There is a clear plastic bag attached to the flat spring that can be used to store instructions. This crib conforms to JPMA-Juvenile Products Manufacturers Association and the CPSC-Consumer Product Safety Commission. Please adhere to the follow- ing guidelines for assembly, operation and maintenance.
Page 6
STEP 2. Attach stationary side to left and right crib ends. Position the stationary side so that the top rail with the plastic teething protector is on top. One of the posts of the left crib end has 3 threaded inserts in it. Bolt the stationary side to the left crib end by inserting 3 of the 1 "...
Page 7
STEP 3. Install crib spring. 1. The scissors brackets allow the crib spring to be installed at 3 different heights. The longer arm of the scissors bracket is attached to hole "A" for shipping purposes (see SECTION "C"). The bolts and nuts for the shorter arm are attached to the edge of the metal frame in holes "C"...
Page 8
STEP 4 Attach drop side to left and right crib ends. Position the drop side so that the teething protector and the keyhole slot (see SECTION "D") is on top. There is a label on the bottom rail of the drop side that says “PUSH”. Make sure this label is turned to the outside of the crib so that the drop side will release and lock properly.
Page 9
STEP 5. Tighten stabilizer rails and the stationary side of crib. With the allen wrench provided, tighten the 4 decorative bolts that were used to attach the stabilizer rails. Also tighten the 6 bolts used to attach the stationary sides. STEP 6.
Page 10
STEP 8 Assemble drawer divider and sides to drawer back. Lay the drawer back down so that the groove is facing up as shown in the diagram below. Insert a capped connector bolt through the center hole in the middle of the drawer back Align the wooden dowels in the end of the drawer divider that is marked “back”...
Page 11
STEP 9 Install crib drawer bottoms. Orient one of the crib drawer bottoms so that the “NO STEP” warning label that is on the white side of the drawer bottom is facing the top and the front of the drawer assembly. Insert the drawer bottom into the grooves along the bottom edges of the drawer side and drawer divider.
Page 12
STEP 10 Attach drawer front to crib drawer. With the use of a flat head screwdriver, install threaded connecting bolts into the middle holes that are drilled on the back of the drawer front at each end and the center (refer to SECTION “A”). Use care not to over tighten these bolts to avoid damage to the drawer front.
Page 13
STEP 11 Installing the crib drawer. Extend the drawer guides outward that are mounted near the bottom of the left and right crib ends. With the help of another person, align the drawer guides that are mounted on the drawer sides with the guides that are mounted on the crib ends.
Page 14
CAUTION: A 1 /4 5 /8 ny mattress in this crib must be at least 27- " by 51- " with a thickness of no less than 5 inches and not exceeding 6 inches. 5"MINIMUM THICKNESS MATTRESS 6"MAXIMUM THICKNESS CRIB SPRING FRAME Operating Drop-Side 1.
Page 15
CLEANING: Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Need help?
Do you have a question about the 579-84-215 and is the answer not in the manual?
Questions and answers