Subscribe to Our Youtube Channel
Summary of Contents for ADIATEK baby
- Page 1 XFC baby plus Li 07 2016 Use and maintenance Attention! Please read the instructions before use.
-
Page 2: With Support
TECHNICAL DESCRIPTION Cleaning width Squeegee width Battery voltage Battery capacity Power rating Brush motor Suction motor Working capacity, up to 1240 1240 1240 Brush diameter Brush rpm giri/min Brush pressure Suction vacuum Mbar Type of drive semi. aut. semi. aut. semi. -
Page 3: Table Of Contents
INTRODUCTORY COMMENT Thank you for having chosen our machine. This floor cleaning machine is used for the commercial cleaning and is able to clean most types of hard floor, except carpet cleaning (if unsure please consult your floor manufacturer/supplier). During its forward movement, the combined action of the brush and the detergent solution removes the dirt which is recovered through the rear suction assembly, giving a perfectly dry surface. - Page 4 Brush replacement Rear squeegee rubber replacement Front squeegee rubber replacement TROUBLESHOOTING GUIDE The suction motor does not work The brush motor does not work Insufficient water on the brush The machine does not clean properly The squeegee does not dry perfectly Excessive foam production Led (2), (3) and (4) become red PROGRAMMED MAINTENANCE...
-
Page 5: General Rules Of Safety
GENERAL RULES OF SAFETY CORRECT USE − Do not use the machine on surfaces covered The rules below have to be followed carefully in order to avoid injury to the operator and damage with inflammable liquids or dusts (for example to the machine. -
Page 6: Legend Instrument Board And Controls
LEGEND INSTRUMENT BOARD CONTROLS SQUEEGEE LIFT LEVER ON/OFF SWITCH WITH SIGNAL SIGNAL LAMP HANDLE BARS BRUSH MOTOR SWITCH WITH SIGNAL LAMP SCRUB CONTROL LEVERS SUCTION MOTOR SWITCH WITH SIGNAL LAMP HANDLE BAR RELEASE LEVER SOLENOID VALVE SWITCH WITH SIGNAL LAMP LEGEND MACHINE WHEELS 16. -
Page 7: Symbology Machine
SYMBOLOGY MACHINE Symbol 0/1 indicating the Symbol that indicates the ON/OFF switch and its signal position of the outlet plug lamp. of the solution tank. Symbol denoting the switch This symbol indicates that for the water opening and tanks need the signal lamp that the emptied before rotating the water is open. -
Page 8: Before Use
BEFORE USE To rotate the handle bar into one of the different working positions: HANDLING OF THE PACKED MACHINE Pull up the release lever (8) near the handle The machine is supplied with suitable packing. bars. The total weight for agm is: 75 kg (max). Rotate the handle bar into the working The total weight for xfc is: 80 kg (max). -
Page 9: Disassembly Of The Batteries (Standard Agm Version)
Lift and remove the recovery tank (16) holding it from the provided handles. One on the front and one on the rear of the tank (shown with small arrows in the drawing below). Connection Lithium battery: Connect the battery connector (1) to the machine connector. -
Page 10: Disassembly Of The Batteries (Version Plus With Xfc Batteries)
Unscrew the battery stop (2). To reassemble everything, repeat the above indicated procedure inversely. DISASSEMBLY OF THE BATTERIES (VERSION PLUS WITH XFC BATTERIES) Take off the first battery (3). To disassemble the batteries from the machine, it is necessary to follow below procedure: Disconnect the connector bridge (1) holding it by the connector and not by the cable. -
Page 11: Disassembly Of The Battery (Version With Lithium Battery)
DISASSEMBLY OF THE BATTERY (VERSION Take off the first battery (4). WITH LITHIUM BATTERY) To disassemble the battery from the machine, it is necessary to follow below procedure: Disconnect the battery connector (1). Uncouple the battery stop (3) making it slide along the slot until it comes off. -
Page 12: Battery Charging (Plus Version With Xfc Or With Lithium)
BATTERY CHARGING (PLUS VERSION WITH XFC OR WITH LITHIUM) If the machine is equipped with XFC batteries, a suitable label with the "plus" logo is fixed on the rear machine frame. This identifies the version equipped with pure lead batteries (XFC) and with its dedicated battery charger. -
Page 13: Batteries Disposal
Open the screw plug (15) situated on top and fill the solution tank with clean water at a maximum temperature of 50°C. Add the liquid detergent in percentage recommended manufacturer. To avoid excessive foaming, which could cause problems to the suction motor, use the minimum percentage of detergent. -
Page 14: Handle Bar Adjustment
During the first few meters check that the solution flow is appropriate. The flow adjuster of the solution is already adjusted at the factory to satisfy the cleaning of most floors. If it is necessary to adjust the quantity of solution onto the floor, adjust the lever of the flow adjuster (11). -
Page 15: Security Device Brush Lifting (Optional)
Move the machine to an appropriate place for tank draining. SECURITY DEVICE BRUSH LIFTING (OPTIONAL) security device prevents brush motor activation when the brush is lifted from the floor during operation. To move the machine, push down the handle bar so that the front of the machine rotates upwards pivoting on the main wheels of the machine and consequently the The machine is not equipped with a parking... -
Page 16: Emptying And Cleaning Of The Solution Tank
SUCTION FILTER CLEANING Empty the recovery tank into appropriate containers, according to the standard norms for the liquid disposal. Rinse and clean the tank. Reassemble everything. Take off the suction cover (17) after rotating the blocking levers (B). Take off the filter with the float bending the filter edge to release it from the screws present on the cover. -
Page 17: Brush Removal/Fitting
Lift the front part of the machine rotating it on the rear wheels and bringing it into the vertical position as shown in the figure. The position of the vertical parking is indicated when you expect not to use the machine for a period of more than 2/3 days, to avoid that the weight of the machine may damage the brush compromising hence the correct functioning of... -
Page 18: Ordinary Maintenance
BRUSH REPLACEMENT The brush has to be replaced when the control device brush wear intervenes. It is possible to use also other brush types, depending on the type and dirt of floor to be cleaned (see under “RECOMMENDED BRUSHES”). Remove the old brush and replace it with a new one (see under “BRUSH REMOVAL/FITTING"). -
Page 19: Front Squeegee Rubber Replacement
Release the catch (4) of the rubber blade clamp and take the rubber off to turn it to a new side or replace it. Check that the coupling and the squeegee hose are not obstructed and if necessary, clean the entire assembly. reassemble squeegee reverse... -
Page 20: The Brush Motor Does Not Work
If the problem persists, please contact the Check that the solution flow adjuster (11), authorized technical assistance. placed in front underneath the solution tank, is sufficiently open. Press the brush control levers (5). If the problem persists, please contact the authorized technical assistance. -
Page 21: Excessive Foam Production
Check that the suction motor switch is on. Check the level in the recovery tank (see under “OVERFILL PROTECTION”) and if necessary, empty the tank. If the floor remains wet in the central part of the drying, it is necessary to give more pressure in the rear part of the squeegee, screwing down of some turns the screw, as shown in the picture. - Page 23 RECOMMENDED BRUSHES Brushes must be chosen depending on type of floor and dirt to be removed. The employed material and the bristle diameter are the elements that distinguish different types of brushes. MATERIAL CHARACTERISTICS Good wear resistance. Maintains characteristics with hot water up to 60°C. PPL (Polypropylene) It is not hygroscopic.
- Page 24 Tel. +39 045 877 9086 I-37057 San Giovanni Lupatoto (VR) Fax. +39 045 877 9195 Logistics and Production: Via Saturno, 25 Tel. +39 045 606 6289 I-37059 S. Maria di Zevio (VR) Fax. +39 045 605 0903 www.adiatek.com - info@adiatek.com...
Need help?
Do you have a question about the baby and is the answer not in the manual?
Questions and answers