Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Duevi EzyDriveCAM
- Page 1 EzyDrive EzyDriveCAM EzyDrive EzyDrive D I G I T A L V I D E O R E C O R D E R HARDWARE INSTALLATION MANUAL (VERSION 3.0) Software manual only on CD This manual may be subject to change without notice...
- Page 2 Thank you for choosing our product. We invite you to read carefully these directions before installing and using this device in order to fully make the most of all its capacities. 1. INTRODUCTION THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY IMPROPER USE OF THE PRODUCT, INCORRECT INSTALLATION OR FAILURE TO COMPLY WITH INSTRUCTIONS OF THIS MANUAL AND THE LAW REGARDING ELECTRICAL SYSTEMS.
-
Page 3: Device Connection
2. DEVICE CONNECTION POWER SUPPLY Can be in two different types. When using PoE, do NOT connect 12 V power supply! 12 V POWER SUPPLY Power is supplied by LAN (if present a Power over Ethernet system) LAN connector RJ45 Backup battery type connector +12V... - Page 4 POWER SUPPLY The camera can be powered: power supply 12 ÷ 30 V power supply 24 V The POWER connector does not have preferential polarity (even in case of CC) POF2 Plastic optic fiber Backup battery connector (LAN) connector POF2 LED POF1 Network activity Plastic optic fiber...
-
Page 5: Activity Led
POWER and DATA The camera is powered directly by 230 V power line ® Data communication from/to the camera is made through power line by HomePlug 1.0 system Activity LED Data transfer Backup battery connector 230 V Link LED N = Neutral (blue) F = Phase (brown) Connection to HomPlug system... - Page 6 Input/Output Figure 4 – Input/output connector and special cable scheme Connection of the input Figure 5 – Connection scheme of the digital input to an external detector...
- Page 7 Connection of the output Figure 6 – Connection scheme of the digital output to a relay board to drive a load...
-
Page 8: Before The Installation
3. Installation Before the installation Each EzyCAM device must be configured before its use. At the first start and configuration DO NOT CONNECT neither SD memory cards nor BATTERY, only main power supply and data connection. After first configuration is possible to add SD cards and battery. It is recommended to connect the EzyCAM to be programmed directly to PC and not through a LAN. -
Page 9: Installation And Settings
Installation and settings 1. 1. Mount the lens (standard plug Board-Mount / M12) screwing on the ferrule that surround the CMOS sensor. On some models the lens could be already mounted. WE RECOMMEND to follow carefully the mounting instruction on the lens manual or product manual to avoid to damage of the optical lens. - Page 10 Cables For the cable passage are available two ways: 1) 1) 1) 1) Cable gland: push with strength the cables through the membrane that will be adapted automatically around the cables. 2) 2) 2) 2) Cable path: break it following the form and pass the cable. Cable path Cable gland...
- Page 11 4. LED Power Status Link/Active 100 Mbps Power Device powered Solid Internal firmware working properly Blinking System initialization No power and low battery level System failure Link/Active Solid or LAN connection established Data transferring blinking No connection 100 Mbps Solid Connection speed 100 Mbps Connection speed 10 Mbps...
-
Page 12: Status Led
Status LED This red LED blinks according to status of the EzyCAM: Status Solid Onboard IR detector Blink about every 10 s: system active, waiting for an event Blinking Slow blinking (on 1 s, off 1 s): system active and recording continuously Quick blinking: system active, recording after Motion detection or Input System failure... - Page 13 5. TECHNICALS • power supply not included 11,8 ÷ 26,4 V Power supply • Power over Ethernet P.o.E. ( ): power from LAN if present a P.o.E. system • Absorption MAX 5 W • Battery Rechargeable battery pack (4,8 V –...
Need help?
Do you have a question about the EzyDriveCAM and is the answer not in the manual?
Questions and answers