Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Blue connect
Summary of Contents for Blue connect
- Page 1 U S E R M A N U A L...
-
Page 2: Precautions For Use
» Blue Connect is not a toy. Avoid shocks as they may damage it. » Keep Blue Connect out of reach of children when handling it (e.g. calibration and standby) due to the use of chemicals. Store calibration products out of reach of children. - Page 3 Description of the equipement Blue Connect analyser: Delivered secured on the storage cap to protect the probe during transportation. The probe is immersed in KCI (saturated potassium chloride), which assures its protection. The storage cap: Used to transport the probe out of the water or to keep the sensors immersed during an extended storage (in winter for example).
-
Page 4: App Installation
Maintenance guide: Advises you on the operations to perform to maintain the quality of the water in your pool. Settings: Allows you to configure the settings for your pool and Blue devices, as well as have access to help and technical support. - Page 5 A. How to start up Blue Connect? In the app, in “Settings” » “Blue Connect”, press “Add” and insert the code (key) and the three last digits of the serial number (SN), which can both be found on the back of the start guide or on the storage cap of the device.
- Page 6 Feel free to watch our Blue Connect start-up video available on www.blueconnect.io (help). Blue Fit50 is a Blue Connect accessory. It is available in the Blue Plus pack, or sold separately. Sold separately.
- Page 7 Activate the Internet (Wi-Fi or 4G) and Bluetooth® on your smartphone. NB: Stay close to your device throughout the whole calibration process. In the app, in “Settings“ » “Blue Connect“, press “Calibrate“. A message at the top of the screen indicates that the device is detected.
-
Page 8: Battery Replacement
The battery needs to be replaced approximately every two years. Please contact your reseller to get a new one. NB: To ensure an optimized battery life, put Blue Connect into standby mode when the pool is in winterization. The box includes:... - Page 9 Installation: In “Settings“ » “Blue Connect“, press “Battery replacement“. Take out the device from the water, remove the rubber ring and the usage cap and place Blue Connect on the storage cap. Wipe it and start the procedure in a dry and clean place.
- Page 10 Place the new seal supplied with the battery on the screw thread of the upper part of the device. Close the upper part. This is a left-hand thread. Screw it counter-clockwise. Paste the new adhesive tape supplied with the battery and replace the ring. Then, place the usage cap and place Blue Connect back in the water.
-
Page 11: Probe Replacement
Installation: In “Settings“ » ”Blue Connect”, press “Probe replacement“. Take out Blue Connect from the water. Wipe the device and start the procedure in a dry, clean place. Remove the usage cap and nut. If you struggle to unscrew the nut, use adjustable pliers by placing them on this exact spot (Image A). - Page 12 Screw the nut firmly onto the device. Feel free to use adjustable pliers to tighten it properly. Then, place the usage cap and place Blue Connect back in the water. NB: The sensor may take a few hours to stabilise its parameters after its first immersion in the...
- Page 13 Activate the Internet (Wi-Fi or 4G) and Bluetooth® on your smartphone. NB: Stay close to the device throughout the whole standby process. In the app, in “Settings” » “Blue Connect”, press on “Put into standby mode”. Rinse the storage cap with clean water and wipe it. Place KCI (saturated potassium chloride) or pH4 in the storage cap and screw it.
-
Page 14: Technical Characteristics
Storage: If you need to take Blue Connect out of the pool for more than an hour, screw it on storage cap with KCI (saturated potassium chloride), pH4, or as a last resort, pool water as the probe should not be left dry. -
Page 15: Troubleshooting Guide
Troubleshooting guide Compatibility problem Do not confuse B with 8 and vice versa. between the serial number and the code. No Sigfox® connection. 1. Check your Sigfox® coverage on www.sigfox.com. 2. Make sure the upper part of the device is out of the water to allow the communication system to operate. - Page 16 Introduction A. Overview The Blue Fit50 is a hose clamp compatible with Blue Connect. It allows to install Blue Connect in the technical room. Note: Blue Fit50 is a Blue Connect accessory. It is available in the Blue Plus pack, or sold separately.
- Page 17 With a 40mm diameter hole saw, drill a hole in the upper part of the pipe. Note: The Blue Connect must be in vertical position, with the probe downwards. Place both parts of the hose clamp on each side of the pipe so that the holes coincide, and screw the hose clamp.
-
Page 18: Winterization Procedure
Slightly and slowly unscrew the Blue Connect (maximum ½ turn) to remove any air. As soon as the water comes out, it means that there is no air left in the pipes, and you can then tightly screw Blue Connect again. -
Page 19: General Information
In the app, in “Settings“ » “Blue Connect“ press “Put into standby mode“. Rinse the storage cap and wipe it. Add KCl (saturated potassium chloride) or pH4 in the storage cap and screw it. Validate the standby mode and store Blue Connect sheltered from frost. -
Page 20: Registered Trademark
Registered trademark Riiot Labs, Blue Connect and Blue Fit50, as well as their respective logos, may be trademarks or registered trademarks of Riiot Labs S.A. Fluidra as well as their logos are trademarks or registered trademarks of Fluidra S.A. The Bluetooth® brand (and its logo) is a registered trademark and is the property of Bluetooth SIG, Inc. - Page 21 - Reorient or relocate the receiving 5404014411114 antenna. - Increase the separation between the equipment 5404014411138 and receiver. - Connect the equipment into an outlet on 5404014411213 circuit different from that to which the receiver is connected. 5404014411233 - Consult the dealer or an experienced radio/TV technician for help.
Need help?
Do you have a question about the connect and is the answer not in the manual?
Questions and answers
How do you get it operational again after it has been out of your pool in Standby Mode?
To operate Blue Connect after it has been in Standby Mode, follow these steps:
1. Remove from Storage: Take Blue Connect from its storage place after hibernation.
2. Reactivate via App:
- Open the Blue Connect app.
- Go to the "Settings" section.
- Select "My Blue Connect."
- Scroll to the bottom and deactivate Standby Mode.
3. Wake Up the Device:
- Place Blue Connect as shown in the instructions.
- Shake it with a firm motion until you hear beeps.
4. Confirm Connection:
- Go back to the app to check if Blue Connect is connected.
5. Start the Device Manually:
- Place Blue Connect in an upright position.
- Remove the storage cap and empty the protective liquid.
- Rinse and store the cap for future use.
Now, Blue Connect is ready for operation.
This answer is automatically generated