Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for System Q PTZ705
- Page 1 MINI 3D Keyboard PTZ705 INSTRUCTION MANUAL Version 4 19/06/2015...
- Page 2 Keyboard Controller Parameters Item Description Power Supply DC12v 1A -10̊ C - +55̊ C Temperature Humidity <90%RH Communication RS485 Half duplex Baud Rate 2400, 4800, 9600, 19200, 38400bps Screen 128 x 32 LCD screen Dimensions 180 x 165 x 90mm List of Additional Items Name Quantity...
-
Page 3: Keyboard Controls
Keyboard Controls Function Keys Setup Preset Tele Wide Shot Near Pattern Open Close Auto Joystick LCD Screen Function Keys PTZ camera setup and recall keys. Exit key: Exit and back to previous menu Setup Setup key: press and hold for 3 seconds to setup parameters Adjust control speed. -
Page 4: Lcd Screen
Pattern Starts/stops pattern record. Press for three seconds to start pattern record. After completion press this key again to stop recording. Use together with number key. Runs the stored pattern. Use together with number key. 0 ~ 9 Number keys 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 Auto Controls PTZ rotation in a horizontal direction automatically or clears input number. - Page 5 Joystick CAMERA NORMAL MODE CAMERA SETUP MODE...
- Page 6 KEYBOARD CONTROLLER OPERATIONS 2.1 Introduction to single-press keys & combined keys 2.1.1 Single Press key: When a single key is pressed the corresponding PTZ will respond. Single press keys Include: Near, Far, Tele, Wide, Open, Close, Auto, F1, Run, Esc and Joystick.
- Page 7 2.2.3 Set and call preset point: Set preset point 1: key in 1, press [Preset) . Call preset point 1: key in 1, press [Shot) . 2.2.4 Turn on/Turn off aux function Turn on : Open aux. function, press 1, press AUX on. Turn off: Close aux.
-
Page 8: Parameter Setup
Parameter Setup PTZ Parameter Setup Example: Change protocol for PTZ 28 to PELCO-P and baud rate to 9600. Key in password (default: 8888), press joystick, then LCD will display: Press joystick, LCD will display: Move the joystick towards the left/right to select PTZ 28, then LCD will display: Press joystick and LCD will display: Move the joystick right and LCD will display: Press joystick, finish protocol setup and switch to baud rate setup, the LCD will display:... -
Page 9: System Parameter Setup
System Parameter Setup System parameters include : Language, password, key-press volume, key backlight, and default factory setup. The following example is the default factory setup operation steps: In normal status, press and hold Setup key for more than 3 seconds to display: Key in password (default password:8888) press joystick and LCD will display: Move the joystick down the LCD will display: Press joystick and LCD will display:... -
Page 10: Ptz Setup
Parameter Setup Diagram PELCO-D, PTZ addr : xxx Protocol PTZ SETUP PELCO-P PTZ addr : 0.254 2400, 4800, 9600, Baud Rate 19200, 38400 (All PTZ parameters will be set the same) Language Chinese, English Move joystick to select Old Password : 4 digit number Password Setup New Password :... - Page 11 4. Typical Connections Diagram...
-
Page 12: Frequently Asked Questions
5. Frequently Asked Questions Symptom Action Information a. Check RS485 + and – are Keyboard does not control 1. Check RS485 hardware the PTZ camera correct at both ends. b. Check RS485 continuity 2. Check RS485 software a. Check address, protocol settings address, protocol and and baud rate agree with that baud rate... - Page 13 All specifications are approximate. Kovert.com reserves the right to change any product specification or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, kovert.com cannot be held responsible in any way for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non-performance of the camera or other equipment that these instructions refer to.
Need help?
Do you have a question about the PTZ705 and is the answer not in the manual?
Questions and answers