Advertisement
Step 4 Install the doorbell.
Step 3 Connect the power cables.
Make sure you have powered off the main power switch of your home.
●
-Drill 2 holes on the wall according to
Connect a resistor (included in the box content) to the doorbell if no
1
●
The suggested installation
the mounting template.
electrical chime or mechanical chime is connected.
-Insert the expansion tubes into the
distance is only for your
- Loosen the screws on the rear panel of the doorbell, put loops of power
drilled holes.
reference.
cables (included in the box content) into the screws, and then tighten them.
- Pull the power cables from the wall, and connect to the power connector.
- Connect the power cables to the power connector (included in the box
content).
96°
Power
Do not grate your nails or other
Connector
objects on the len's glass when
20 to 30 cm
Power Cable
installing the doorbell.
8
9
Getting Started
Step 1 Power on the doorbell.
Make sure you have connected the power cables for the doorbell.
Power on the main power switch of your home.
- Route the cables and insert cables and power
2
When the blue light is on, the doorbell is powered on.
connector into the wall.
- Align the screw holes on the doorbell body with the
drilled holes on the wall.
Step 2 Set the Guarding Vision App.
- Fix the doorbell body to the wall tightly with 2
1
Install Guarding Vision App and register a user account.
screws.
- Connect your mobile device to Wi-Fi.
Expansion
Screws
- Download and install the Guarding Vision App by searching "Guarding
Tube
Vision" in App store or Google Play
- Put the faceplate to cover the doorbell body.
3
- Use 1 set screw to fix the faceplate with the
doorbell body tightly.
- Launch the App and register for a Guarding Vision user account.
2
Log in to the Guarding Vision App.
- Connect your mobile device to Wi-Fi.
- Start the Guarding Vision App, and input the Guarding Vision user account
Set Screw
to log in to the App.
10
Step 3 Activate the doorbell and add it to the Guarding Vision App.
1
Scan QR code or input the serial No. of the doorbell.
- In the Home page of the Guarding Vision App, tap "+" on the upper-right
corner to add the doorbell.
- Scan the QR code or input the serial No. on the front panel of the
doorbell body.
TM
.
OR
2
Connect Wi-Fi.
The doorbell supports 3 kinds of Wi-Fi mode: 802.11 b only, 802.11 g
only, and 802.11 bg only.
The network connection page will pop up after scanning the QR code of
the doorbell successfully.
- Tap Connect to a Network.
- Choose Wireless Connection to set the Wi-Fi connection.
11
12
Operating Doorbell
- Input the Wi-Fi password that your mobile phone has connected to.
Via the Guarding Vision App, you can realize some certain functions of the
- Hold the reset button for 5 seconds.
doorbell (including, but not limited to, live view, and remote playback).
- After hearing the voice prompt "Start configuring Wi-Fi.", tap Next in 3
minutes to start the Wi-Fi connection.
Activate the doorbell.
3
The activation page will pop up after finishing the Wi-Fi connection.
- Tap Set Device Password and input a password to activate the doorbell.
- Tap Activate in the next page to finish activating.
......
......
Link the Guarding Vision account.
4
- Input the verification code of the doorbell in the pop-up page after
activation.
This step is only necessary for adding the doorbell by inputting the serial No.
Video Intercom
- Tap OK to finish adding the doorbell to the Guarding Vision account.
Press
Call Button
on the doorbell.
You can accept the call via the
Guarding Vision
App, get the live view of the
doorbell, and capture the snapshots.
Live View
Guarding Vision
Launch the
App and you can get the live view of the connected
devices.
Playback
Launch the Guarding Vision App, tap a connected device and tap Gallery to
play back.
13
14
Recording
- Check the TF card status by tapping Storage Status in the Device Settings
page.
- If the TF card status displays as Uninitialized, tap to initialize it. The status will
then change to Normal. You can then start recording any event triggered
video in the camera of the doorbell such as motion detection video.
Alarm Notification
Launch the Guarding Vision App and tap Message to see the alarm messages,
such as motion detection alarm message.
The messages will be pushed automatically by enabling Message Push
●
Notification.
The App can receive the triggered alarm automically when the doorbell is
●
powered on by enabling Auto-Receive Alarm after Powering on.
15
Advertisement
