Summary of Contents for 911SafeTrack S4
- Page 1 S4 Vehicle Security Tracker Installation Guide SAFETY-- SECURITY-- SIMPLICITY! 911SafeTrack.com...
- Page 2 In no event shall 911Tracker, Inc. be liable for any damages of any kind, arising out of or related to the use or inability to use this document. S4 Vehicle Security Tracker Installation Guide IG1710A (1.1)
-
Page 3: Table Of Contents
Vehicles Equipped with Airbags Tools Suggested for Installation Equipment List Install your Tracker Step 1 – Register your S4 Tracker Step 2 – Select Your Installation Location Step 3 – Mount S4 Step 4 – Routing Cable Step 5 – Connecting Cable Step 6 –... -
Page 4: Introduction
S4 Tracker in your vehicle. Prior to installing your S4 in your vehicle, you must register your S4 with 911SafeTrack. Please review the User Guide included in the packaging and 911SafeTrack.com for information on how to set S4 mode and S4 Emergency Contacts. -
Page 5: Vehicles Equipped With Airbags
Installer must use caution to identify any airbag wiring and avoid cutting, testing or tapping into airbag wiring. Failure to comply may cause airbag to inflate; this could cause serious injury. • Contact vehicle manufacturer’s corporate headquarters for specific airbag information for the vehicle. 911SafeTrack.com... -
Page 6: Tools Suggested For Installation
• Screwdriver set • Torx socket set • Wire cutter/stripper • Pliers • Flashlight • Multimeter Equipment List S4 Tracker (Front View) S4 Tracker (Side View) Terminal 1 Red (G) Green (C) Connector Cable C1310 Battery B1302 Installation Kit (Velcro set, zip-ties, wire connectors) -
Page 7: Install Your Tracker
S4 may also be installed in a hidden location such as in the glove box or in a console, which is accessible by the Owner. - Page 8 • DO NOT mount the S4 under the hood of the vehicle • DO NOT mount the S4 where it will be exposed to moisture • DO NOT mount the S4 in a spot that will impede safe vehicle operation 911SafeTrack.com...
-
Page 9: Step 3 - Mount S4
Cable, backup Battery, and S4 Installation Kit. You should first mount the S4 Tracker, then install the Cable, then plug in the Cable, and then plug in the backup Battery. S4 must be mounted with the 911SafeTrack label pointed up so the internal GPS antenna is toward the sky. -
Page 10: Step 4 - Routing Cable
HARNESS TAPED IN YELLOW OR BEARING YELLOW “SRS” (SUPPLEMENTAL RESTRAINT SYSTEM) TAGS. Use wire ties to secure wiring from being pulled out of the S4 and to ensure that the Cable does not interfere with any vehicle components. Cable has four wires to be connected: Black –... -
Page 11: Step 5 - Connecting Cable
12-volts when the key is On (will show on your multimeter). Connect the S4 white wire to the existing vehicle wire using one of the S4 Installation Kit wire connectors to capture the vehicle wire and use pliers to squeeze tightly. - Page 12 “Panic” button, you can connect the security module output to the yellow wire to alert S4 if you press the panic button for more than 8 seconds. 12v Power (red wire with fuse) -- Using the shop manual...
- Page 13 Out #2 for brief pulse operation that maybe used for door unlock, door lock, flash headlights, sound horn, etc. Out #1 12v Power (pink wire with fuse) – Connect the S4 pink wire to same the same vehicle wire [HOT AT ALL TIMES] that was used for the S4 red wire.
-
Page 14: Step 6 - Testing Cable
S4 configuration in Step 7. If you have connected Out #1 or Out #2, perform the following checks [Do not plug the Cable into the S4 Connector]: • To verify Out #1 operation, carefully touch a test wire... - Page 15 If all Cable tests are confirmed, then -- Plug the Cable into the S4 Connector. After a few seconds, S4 green LED (labeled C) and the red LED (labeled G) will turn On. After a couple minutes, the red LED will start flashing, showing GPS satellite lock.
-
Page 16: Step 7 - Testing Basic S4 Operations
LED is On and the red LED starts to blink. Note: The red LED may take a few minutes to start blinking. Installer uses any cell phone to send S4 a text message 12345 gps (note space after PIN) and checks to verify that the S4 replies with a location text message. - Page 17 (or keyfob “Panic”) for at least 8 sec. The S4 can be programmed by SMS to detect an alarm signal that is either high (12v) or low (0 v). When S4 receives the correct high or low alarm output signal, Installer will receive an Alarm Sounding text notification.
-
Page 18: S4 Security Information
S4 operations have been verified, then the Installer or the Owner sends a text message that sets the Owner’s mobile phone in the S4. Once this is done, S4 will only respond to incoming phone calls from the Owner’s mobile phone. -
Page 19: Troubleshooting
Cable. The fuse is a regular plug-in automotive fuse, 2 Amp. Temporarily unplug Cable from the S4 and confirm that the red wire on terminal 3 is providing 12-volts. Green LED S4 is powered On and searching for continues blinking cellular connection. -
Page 20: Warranty Limitations
USE OR OTHER CAUSES UNRELATED TO DEFECT IN MATERIAL OR WORKMANSHIP. Water Resistance The S4 Tracker is to be placed inside of the vehicle in a location that is not exposed to precipitation. S4 Tracker is not waterproof and will not function when exposed to water.