Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HealthMaster YD-2089
Summary of Contents for HealthMaster YD-2089
- Page 1 HealthMaster Blender ™ O W N E R ’ S M A N U A L...
-
Page 3: Table Of Contents
& accessories assembling the HealthMaster™ Blender 6 - 9 using your HealthMaster™ Blender controls using the tamper HealthMaster™ Blender helpful hints cleaning and maintenance 13 - 14 frequently asked questions warranty information troubleshooting replacement parts order form... -
Page 4: Important Safeguards/Specifications
Never force the plug into the outlet. If it doesn’t fit after trying it one way and • Never add ingredients to the HealthMaster™ Blender while unit is running at a speed of higher than #1. then reversing it … contact an electrician. Do not modify the plug in any way. -
Page 5: Parts & Accessories
Safety Valve Release E-Z Lock Cap IMPORTANT: Your HealthMaster has been shipped with the following components. Check everything carefully before use. If any part is missing or has Handy Tab been damaged in shipping do not use this product and contact shipper using for easy open &... -
Page 6: Assembling The Healthmaster™ Blender
HealthMaster Blender ™ 1. Place the motor Base on a stable, dry surface. BEFORE ASSEMBLING: Unwind power cord to desired length. WARNING: Do not plug power cord into electrical outlet until unit is fully assembled. This appliance was designed with built-in power cord storage beneath the Base. - Page 7 assembly (cont.) 2. Firmly seat the Pitcher onto Fig. B the motor Base while aligning the white dot on the Pitcher with the REMOVE symbol on the Base. (See Figure B) 3. Rotate the Pitcher clockwise until Fig. C the dot symbol on the Pitcher aligns with the Arrow symbol on the Base.
- Page 8 assembly (cont.) NOTE: At this point you may want to place the ingredients for processing into the unit. Insert ingredients into the Pitcher, soft foods first, harder items last. The E-Z Lock Cap can be removed during operation to add additional ingredients or to insert the Tamper. The E-Z Lock Cap should only be removed at speed #1. Always replace Cap when you are finished inserting Tamper or additional ingredients.
- Page 9 assembly (cont.) 5. Place Lid on the Pitcher and push firmly down into place. 6. Make sure the unit is assembled properly before connecting the power cord to the electrical outlet. Once plugged in and ON/OFF button is pushed, ON/OFF lamp turns red and LCD display turns on to show you have assembled the blender properly.
-
Page 10: Using Your Healthmaster™ Blender
HealthMaster Blender ™ 1. After assembling and plugging in the blender, you have to push ON/OFF button, then ON/OFF lamp turns red and LCD display turns on to show you have assembled the blender properly. 2. BEFORE pushing the RUN, PULSE, or ICE button — hold the top of the assembled unit to prevent tipping when starting. -
Page 11: Controls
ICE: Pressing the ICE button causes the burst of speed for each pulse until you blender. If the speed was not set the HealthMaster to operate on a cycle of 1 have achieved the desired results. The HealthMaster will run at speed 1. The second on and 4 seconds off. -
Page 12: Using The Tamper
using the tamper The Tamper is useful when preparing thick or frozen mixtures. The Tamper can be used while the machine is running. 1. Make sure Lid is secured in place. 2. Remove E-Z Lock Cap from Lid. 3. Insert Tamper through the opening in the Lid. 4. -
Page 13: Healthmaster™ Blender Helpful Hints
Blade and cause the motor to malfunction. • Unless otherwise instructed, insert wet ingredients into the HealthMaster™ Blender first, then dry ingredients, then ice if needed. • Thoroughly wash all fruits and vegetables before juicing to remove any dirt or chemicals. - Page 14 using the Blender (cont.) Once off, carefully remove the blade by pulling it out of the bottom of the Pitcher. Wash and dry blade completely. For safety reasons, do not touch blades directly with your hands. NOTE: When reassembling the blade, be sure to tighten the black screw Cap so the blade does not loosen.
-
Page 15: Frequently Asked Questions
frequently asked questions This summary briefly answers common questions. Read operating manual before use. What is the Pitcher made out of? What is the wattage? It is made of a BPA free plastic. 700 watts How many speeds does the unit have? How often should I change my Blades? The unit has 8 variable speeds. -
Page 16: Warranty Information
The manufacturer warrants that your HealthMaster™ Blender is free of defects in materials and workmanship and will, at its option, repair or replace any defective HealthMaster™ that is returned to it. The HealthMaster and its parts and components are warranted for 60 days from the original date of purchase. -
Page 17: Troubleshooting
NOTE: The HealthMaster™ Blender is a very powerful unit. When operating properly, the motor gives off a loud but smooth sound that changes in pitch as the motor speed is increased. This is normal. PROBLEM POSSIBLE REASONS AND SOLUTION There was a burning smell when the blender was •... -
Page 18: Replacement Parts Order Form
E-mail ___________________________________________________________ To order please call or for more information visit: Please make checks payable to: HealthMaster™ Blender www.myhealthmaster.com Mail Payment Today To: HEALTHMASTER, 26 Barnes Industrial Rd. North, or call 1-973-287-???? — 8:00am–9:00pm EST Monday–Friday P.O. Box 3125, Dept. ????, Wallingford, CT 06494... - Page 20 Congratulations on your purchase of the HealthMaster™ Blender. We are very proud of the functional design and exceptional quality of this product. Our manufacturing process is geared to deliver long years of product service to our valued customers. Should you experience any problem with your purchase, our dedicated customer service staff is here to serve you.
Need help?
Do you have a question about the YD-2089 and is the answer not in the manual?
Questions and answers