1. Manuals
  2. Brands
  3. KBC Manuals
  4. Modem
  5. FTDR-S2-WSB
  6. User manual

KBC FTDR-S2-WSB User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FTDR-S2-WSB
User Manual

Advertisement

Table of Contents
loading

Summary of Contents for KBC FTDR-S2-WSB

  • Page 1 FTDR-S2-WSB User Manual...

  • Page 2: Table Of Contents

    ……………………….……………………………..3 1.1 Introduction 1.2 Technical Specification……………………………...………….3 1.3 Warranty .…………………...……………………….…..……...4 1.4 Instruction of Disassembly………………...……….…..……...5 2. Installation ................6 2.1 Package Contents ………………………………………..…..6 2.2 FTDR-S2-WSB Enclosure ............6 2.3 Caution ................…10 2.4 Install Application ..............…10 3. Dimensions ...............12 Manual-FTDR-Rev1311.pdf Page 2 of 12 www.kbcnetworks.com...

  • Page 3: Overview

    The data communication protocol is transparent and compatible with all the RS232/RS422/2 wires RS485/4 wires RS485 upper protocols. The FTDR-S2-WSB series Fiber Optic Modem can be widely used, such as Industrial Controls, Intelligent Transportation Systems (ITS), Industrial Networking, Supervisory Control and Data (SCADA) and so on.

  • Page 4: Warranty

    Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Manual-FTDR-Rev1311.pdf Page 4 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.

  • Page 5: Instruction Of Disassembly

    (jump wire); Snip off power conducting cable and remove power switch /jack/etc.; Take out all PCBs; Disassembly of product completed. Notice：When a product reaches the end of it’s life—return to KBC Manual-FTDR-Rev1311.pdf Page 5 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.

  • Page 6: Installation

    2 Installation 2.1 Package Contents • One FTDR-S2-WSB Multi-Drop Self-Healing Ring Fiber Optic Modem • One power supply adaptor • One User Manual Please contact dealer or distributor if part is missing or damaged. 2.2 FTDR-S2-WSB Enclosure The Top View...
  • Page 7 The terminators can be switched on or off according to the RS485 bus connection. When the fiber transmitter or receiver is placed at the end point of bus, the terminators are usually switched on, but Manual-FTDR-Rev1311.pdf Page 7 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.
  • Page 8 C2A and C2B are open, if the secondary ring is normal. Situation 2: S2 is on C2A and C2B are short circuit, if the secondary ring is failure or the power is off. Manual-FTDR-Rev1311.pdf Page 8 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.
  • Page 9 2 wires RS485/ 4 wires RS485 Transmit Data. Flash if there is activity. RS232/RS422 Transmit Data. Flash if there is activity. RXD: RS232/RS422 Receive Data. Flash if there is activity. Manual-FTDR-Rev1311.pdf Page 9 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.

  • Page 10: Caution

    Fiber Optic Modem should be set in the primary mode, the others are set in the secondary mode. 2.4 Install Application Dip1=OFF Dip1=OFF Dip1=OFF Dip1=OFF Notice: In figure1, all the FTDR-S2-WSB Fiber Optic Modem should be set in the primary mode. Manual-FTDR-Rev1311.pdf Page 10 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.
  • Page 11 The primary fiber ring loop direction is clockwise The secondary fiber ring loop (outside loop) be made up of: A-FTX2 D-FRX2 D-FTX2 C-FRX2 C-FTX2 B-FRX2 B-FTX2 A-FRX2 The secondary fiber ring loop direction is anti-clockwise Manual-FTDR-Rev1311.pdf Page 11 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.

  • Page 12: Dimensions

    3 Dimensions (mm) Manual-FTDR-Rev1311.pdf Page 12 of 12 www.kbcnetworks.com Copyright © KBC Networks Ltd.

Table of Contents