Advertisement
nerKon
Operating
instructSons of
the multifunctional electromagnetic belt
MRK-505
operating instrucions
X
The machine
is designed
with six buftons
I
upper left
is
intensity
button"-",
the
middle
is
ON/OFF
buttons(stratup
and
shutdown),
upper
right
is
intensity button"+". Lower left is
HEAT
button( sauna), the middle is
EMS(
low-
frequency
pulse), lower right
is
VIB
button(vibration)l
X
On
starting up, LCD shows the whole state, what display screen shows
is
the
default mode of strating up:
MODE
:
1.
LEVEL : 00 ; VIB :
0
;
HEAT :
0
X
The
view
of
the
main
part
X
Accessories:
an
operating manual,
a
volume about health knowledge,
a
power adapter dedicated for
the
machine.
X
Time
: working time of the program default
is
15 minutes
{
Operation instructions of buttons
1.
Connect the dedicated power adapter, press
the
button
O
, start up after
hearing
the
sound
"
beep
".
After startup, enter automatically
the
default
state
:
the backlight
of
the LCD screen
is
on, the red LED lights, the intensity
of the
heating
function(HEAT) is "0", discharge function(EMS)
is
for
mode
(MODE) intensity
is
"00", intensity of vibration
function
(VlB) is
"0'.
2.
After startup, in any time without any operation or function output, in
this
case,
within
20 seconds
the
machine shut down automatically.
3.
Heating (HEAT) function: each time you press the HEAT button, the intensity
of
heating will circulate in this
way
"0-1-2-H"
4.
Low frequency discharge( EMS) function: each time you press the
button
EMS, low-frenquency discharge
will
convert
a
pattern,
by
"1-2-3-4"
these
four
model cycles. Press
the
button"+", you can increase
the
intensity
of low-frequency discharge, each time you press, the intensity increases
"1",
and "1o"is maximum, at this point to the maximum, and then
pressing
the
button "+" is
invalid.
Press
the
button
'-',you
can reduce the intensity of the
low-frequency discharge, each time you press, intensity reduces "1",
and
"00"is minimum,
so far as the
minimum,
then
pressing
the button
"-"is
invalid.(Note:
every
conversion model,
the
intensity
of the
new
pattern
begins from "00".)
Vibration
(VlB)
function:
each time
you
press
the
button
VlB,
vibration
intensity will circulate
from
"0-1-2-3-0f'.
--
Note
1:
3), 4), 5) these
three functions,
can be
executed
simultaneously,
also can be used alone.
--Note 2:
when
using
the
"low-frequency
discharge" funcion,
bipolar
electrode slice must cling to the skin to work
properly,
in case the
sudden
current enhance
wounding,
we
made
such
a
technological
protection
measures.
(This
is
new).
lncrease
the
temperature control function
to
control the
temperature within
a
certain range (such
as:
surface temperature
will
be
locked up
to
65 degrees). This
function
is
especially important in high heat
Ejrade
(HEAr-3)
Technical parameters
1,
the normal working
conditions
a)
Ambient
temperature:
10 "C
-40 'C
b) Relative humidity: <80%
c)
Atmospheric
pressure: 700hPa-1 060hPa
d
)
Power
adapter
:11O-220V
50H2, 5V
/
'1.5A
dedicated power
supply
2.
Performance index
e)
Timing
range:
15 min
f)
Power
consumption:
<0.5W
g)
Skin electrode low-frequency pulse output frequency
/ S: 4
times,
8
times,
15
times, 30
times
h)
Output waveform: square
wave,
rectangular wave,
saMooth,
kiangle
wave,
peaked-wave, step
wave.
l) The
heat
treatments temperature: 30 degrees, 40 degrees, 50
degrees,
60 degrees, 70 degrees.
Common
faults
and
solutions
'l
:I YAfi
KANG
)r
rn&nu&i
xnqiixh
6.
x
x
:onducior
rnagletic
rrl::;rer*
Advertisement
Table of Contents
Need help?
Do you have a question about the MRK-505 and is the answer not in the manual?
Questions and answers