Summary of Contents for SensaTyre TPE01A
- Page 1 Tire Pressure Monitoring System User Manual Pressure Range:0~80 PSI Model:TPE01A (Cap Type) TPV05A (Valve Type) TPV03A (Valve with Antenna Type) TPC03A (Clamp Type)
- Page 2 Table of Content...
- Page 3 (2) The tire pressure monitoring system –TPV05A/TPV03A/TPC03A starts to detect pressure and temperature automatically when the vehicle is in motion. The tire pressure monitoring system - TPE01A starts to detect pressure and temperature automatically when the sensor is mounted. Pressure and temperature data will be showed on the LCD screen of digital receiver.
- Page 4 4.4 Strap 4 pcs ! 4.5 Power Cable 1 pcs ! 4.6 Receiver’ Holder 1 pcs ! 4.7 Transmitter 4 pcs ! 4.8 Transmitter 4 pcs ! 4.9 Transmitter 4 pcs ! With Antenna Installation of TPMS ! 6 6 6 6 ! ! ! ! 6 / 2 6 / 2 6 / 2 6 / 2 Install Receiver (1) Install the Receiver’...
- Page 5 ??P ??P (5) Turn on the KEY SW, the Receiver will show ??P /! ??P ??P (6) Reverse above steps to remove the receiver. 5.2 Install Transmitter Attention: Transmitters must be installed by professional technicians. The technicians have to follow the installation guide step by step to install transmitters correctly. Following tools and instructions are for technicians, not for end users.
- Page 6 NOTE:NO.8.6(Page 18) 1.1 Search T Y Y Y Y / / / / Search 1.2 Pick Up tire 01 02 03 04 3.Set tightened torque at 9~10 Kgf.cm. 5.2.1 Install Valve Type Transmitter (Before install the tire please set up the ID of the transmitter first, refer to NO.10) See Page:23 (1)Install the Valve type into the valve of tire disc.
- Page 7 (2)Install the Washer into the valve of Transmitter. (3)Tighten the Nut into the valve of Transmitter. Tighten Torque 35~45 Kgf-cm (4)Tighten the Nozzle into the valve of Transmitter. Tighten Torque 2~3.2 Kgf-cm...
- Page 8 (5)Install the tire. (6)Install the Antenna(Only TPV03A). (7) Finished.
- Page 9 5.2.3 Install Clamp Type Transmitter (Before install the tire please set up the ID of the transmitter first, refer to NO.10) See Page:23 5.2.1.1 Please follow the standard procedures to dismount tire from rim. IMPORTANT: 5.2.1.2 Set up the ID of the transmitter and must keep other transmitters away from at least 1m away to avoid taking the same signal Then install the...
- Page 10 5.2.1.6 Wheel Balancing is required after transmitter installation. 5.2.1.7 Reverse the above steps to remove a transmitter. Suggestion:Tell technician that you have installed TPMS before he changes the tire. 6. Digital Receiver Function Description Digital Receiver Diagram, Display Control and Indicators LCD Backlight Set Up Pressure...
- Page 11 6.2 The Receiver Button Function Description 1.Temperature Display temperature of tires after press button . If no data Button received, the corresponding tire pressure will be displayed as “??C”. 35C 35C ??C 36C (Downward In “General Set Up Mode”,acts as downward button to Button) select function and number.
-
Page 12: Alarms And Warnings
2.Exit Set Up Mode Press button again to exit “Setup Mode”. Note Values shown above are for reference only. 7. Alarms and Warnings Pressure Threshold Alarm and Warning *Remark: 1. Tire pressure lower/higher than Manual Pressure Threshold Setting The manual pressure thresholds suggested being Low/High Pressure Warning is initiated lower than 29PSI and higher than... - Page 13 the low pressure warning will remain on the warning value will be 23PSI. display even re-power the receiver. Suggested Action to Alarm When the alarm occurs,reduce speed and proceed to a safe location to check tires. Note The Pressure Deflation Alarm will disappear when the tires are properly re-inflated to correct levels.
- Page 14 7.2 Temperature Threshold Alarm and Warning Note: 1. Tire Temperature higher than Manual The default manual threshold Setting Temperature Threshold Setting Limit is 75° C High Temperature Warning is initiated when detected tire temperature above programmed Temperature Threshold Setting Limit. Example: Warning Actions Include: When the tire temperature is 80°...
- Page 15 7.3 Other Warnings 1. Communication failure warning When the receiver has not received a transmitter signal over 30 mins., the ??? symbols will be shown on LCD display at the ??? 32P corresponding position. If the above 32P 32P symbols continuously remains on the display, the system might be poorly communicated or malfunctioned.
-
Page 16: General Set Up Mode
8. General Set Up Mode 8.1 Manual Low Pressure Threshold Setting Press button for more than 2 Use button (act as downward seconds to go into “General Set Up button) and button (act as upward Mode”. button) to select “Low Pressure Warning “... - Page 17 8.2 Manual High Pressure Threshold Setting Press button for more than 2 Use button (act as downward seconds to enter “General Set button) and button (act as Up Mode”. upward button) to select “High Pressure Warning “ setting. LCD Display will show Use button (act as downward Press...
- Page 18 8.3 Manual Temperature Threshold Setting Press button for more than 2 Use button (act as downward seconds to enter “General Set Up button) and button (act as upward Mode”. button) to select “High Temperature Warning” setting. LCD Display will show Use button (act as downward Press...
- Page 19 8.5 Restore Factory-Preset Value (This function is to restore the manual pressure and temperature threshold value to the factory-preset threshold. The Factory-Preset Low Pressure Threshold Value=29PSI, High Pressure Threshold Value=42PSI; Factory-Preset Temperature Threshold Value=75 ) 1. Press button for more than 2 Use button (act as downward button) seconds to go into “General Set...
- Page 20 Use button (act as downward Once received the TX ID code, the tire button) and button (act as upward pressure will shown button) to select the tire location for associated tire location on the display. setting ID code. Transmitter searching then completes. Press button to cancel the search function and exit “General Set Up...
-
Page 21: Special Set Up Mode
Special Set Up Mode Exchange Wheel Location Simultaneously press button Use button (act as downward for more than 2 seconds to button) and button (act as upward enter “Special Set Up Mode”. button) to select ”Exchange Wheel Location” setting. Press button to confirm. - Page 22 LCD Display will show Use button (act as downward button) and button (act as upward button) to move cursor to select the tire location for ID input Press button New ID confirm. Input 01 02 03 04 Use button (act as downward Double check input ID number to ensure button) and button (act as...
- Page 23 Set Temperature Unit Mode 1.Simultaneously press button 2.Use button (act as downward button) for more than 2 seconds to enter “Special and button (act as upward button) to Set Up Mode”. select ”Set Temperature Unit” setting. The LCD Display will show Use button (act as downward Press button...
- Page 24 5. Press to confirm and return to “Special Set Up Mode”. 32P 32P Exit Special Set Up Mode Press button again LCD Display will return as initial display. 32P 32P 32P 32P Note Value shown is for reference only. 10. Receive ID Mode---LF setting for Clamp/Valve(with Antenna) Transmitter only Power Plug Put the 12DCV POWER CABLE to the...
- Page 25 Simultaneously press button for more than 2 seconds to enter “Receive ID Mode”. Check if the LCD of the Receiver shows. “Receive ID“. Turn on the LF. Left- Right- Front Front Select one of the tires you want to set up. (The signal active distance of LF is Left- Right-...
- Page 26 Put the LF near the transmitter at least 30mm. We suggest that installing the tire after setting. IMPORTANT:When setting,please keep other transmitter away from the setting transmitter at least 1m NOTE: If you are not sure it receives the signal or not please do it again or refer to NO.9.2 “Manual input new transmitter ID code”...
-
Page 27: Limit Warranty
16 As the voltage is below 2.3V,pushing any button will make the “SEND” LED flash every 4secs. NOTE The value above is for reference. 11. Limit Warranty Mobiletron, hereby warrants that this Mobiletron wireless tire pressure monitoring system shall be free from material defects in workmanship and/or materials until the expiry of twelve months from its purchase by the end user, EXCEPT WHERE any such defect has been caused by: Improper or non-normal use, Improper installation, contacts with any corrosive or otherwise harmful substance, any other acts or... - Page 28 incurred in removing the defective parts and/or installing the replacement. (3) The retailer shall at Mobiletron’ cost send any unit which is defective as described in the above warranty to Mobiletron at No.39, Sec 3, Chung-Ching Rd., Ta-Ya, Taichung Hsien, Taiwan 428. 11.2 This Limited Warranty Provided by Mobiletron Does Not Cover (1) Product that have been subjected to abuse, accident, alteration, modification,...
-
Page 29: Technical Specifications
13. Technical Specifications 2 4 / 2 2 4 / 2 !S f d f j w f s 2 4 / 2 2 4 / 2 !S f d f j w f s !S f d f j w f s !S f d f j w f s ! ! ! ! ! ! ! ! 2 4 / 2 4 / 2 4 / 2 4 / 3 3 3 3 !U s b o t n j u u f s... - Page 30 W b m w f !U z q f ! ! ! ! W b m w f !U z q f W b m w f !U z q f W b m w f !U z q f W b m w f !U z q f !x j u i !B o u f o o b W b m w f !U z q f !x j u i !B o u f o o b ! ! ! ! W b m w f !U z q f !x j u i !B o u f o o b...
- Page 31 D m b n q !U z q f D m b n q !U z q f ! ! ! ! D m b n q !U z q f D m b n q !U z q f...
- Page 32 ! ! ! ! 14. Manufacturer Manufacturer: Moniletron Electronic ,Inc. Telephone: +886-4-25683366 Address: No.39, Sec 3, Chung-Ching Rd., Ta-Ya, Fax: +886-4-25673069 Taichung Hsien, Taiwan 428 Web Site: http://www.more.com.tw ! ! ! !
Need help?
Do you have a question about the TPE01A and is the answer not in the manual?
Questions and answers